[cisco-voip] 7906 phones stopped working with CME

[Erick Bergquist]

Also, the tftp debug doesn't even show the 7906 phones trying to TFTP
files. The phones do get a IP Address then just sit and spin.
Looking more like a RMA situation.

On Fri, Sep 12, 2008 at 5:13 PM, Erick Bergquist <erickbee at gmail.com> wrote:
> So does anyone know what this box with checkmark is, versus the circle?
> Does it mean anything?
>
>
> On Fri, Sep 12, 2008 at 4:58 PM, Nikola Stojsin <nikola at att.net> wrote:
>> I would try replacing the firmware file - I ran into a similar problem once
>> before, and problem was traced back to (invisible) data corruption...
>>
>> HTH,
>> Nikola
>>
>>
>>
>> ------------------------------
>> Nikola Stojsin
>> PhD CCIE #12888
>> Nikola at att.net
>> (917) 558-1423
>> (917) 591-9382 (fax)
>> ------------------------------
>>
>>
>> -----Original Message-----
>> From: cisco-voip-bounces at puck.nether.net
>> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Erick Bergquist
>> Sent: Friday, September 12, 2008 5:55 PM
>> To: ROZA, Ariel
>> Cc: cisco-voip at puck.nether.net
>> Subject: Re: [cisco-voip] 7906 phones stopped working with CME
>>
>> Yep, all that has been there for awhile. These phones were working fine.
>>
>> On Fri, Sep 12, 2008 at 4:36 PM, ROZA, Ariel
>> <Ariel.ROZA at la.logicalis.com> wrote:
>>> Eric,
>>>
>>>        You must have the phone firmware file on the router´s flash memory,
>> and make sure that you have the tftp-server command applied too...
>>>
>>> Regards,
>>>
>>> Ariel
>>>
>>> -----Original Message-----
>>> From: cisco-voip-bounces at puck.nether.net
>> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Erick Bergquist
>>> Sent: Viernes, 12 de Septiembre de 2008 06:30 p.m.
>>> To: cisco-voip at puck.nether.net
>>> Subject: [cisco-voip] 7906 phones stopped working with CME
>>>
>>> Hi,
>>>
>>> I have a strange issue, have about 15 7906 model phones on a CME 4.1
>> system and all of sudden all the 7906 phones except 1 no longer function
>> correctly. They worked fine before. They just keep cycling trying to do
>> something, if we put a 7911 model phone on same cable, same switch port, etc
>> it works fine. We've rebooted the CME router also even and the phone is
>> getting a DHCP address from the DHCP server and I can ping it briefly as it
>> cycles.
>>>
>>> On the phone itself, you power it on, the lights blink, then after a
>> couple seconds the Cisco logo is displayed on the LCD and in corner there is
>> square with a checkmark in it on first cycle after a power on.
>>> On subsequent cycles the phone does, it displays logo with a circle in
>> corner with a diamond or square in the circle (can't really make it out).
>>>
>>> What is the factory reset procedure for the 7906?
>>> I tried powering it on with holding down # key and then releasing when it
>> lights up, then entering the 123456789*#0 sequence but that did not make any
>> difference and I let it sit for 15 minutes after doing that.
>>> _______________________________________________
>>> cisco-voip mailing list
>>> cisco-voip at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>