[cisco-voip] Registration rejected on a single FXO port of an MGCP 2801 with a 2FXO card?

Lelio Fulgenzi lelio at uoguelph.ca
Fri Feb 13 14:54:46 EST 2009


Is it plugged in? I think I recall unless it's plugged in, it won't register. 

--- 
Lelio Fulgenzi, B.A. 
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1 
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN) 
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
"Bad grammar makes me [sic]" - Tshirt 


----- Original Message ----- 
From: "Tim Reimers" <treimers at ashevillenc.gov> 
To: cisco-voip at puck.nether.net 
Sent: Friday, February 13, 2009 2:40:55 PM GMT -05:00 US/Canada Eastern 
Subject: [cisco-voip] Registration rejected on a single FXO port of an MGCP 2801 with a 2FXO card? 



What in the world could be causing this? 
I've had registration issues with MGCP equipment in the past, being hostname/domain-name related 
That makes the entire device not register. 

But I've never seen one port get rejected and the other one not! 
Weird. 








Product Cisco MGCP FXO Port 
Gateway TransitGW2801.mydomain.local 
Device Protocol Analog Access 
Registration Rejected 
IP Address 192.168.XXX.252 
End-Point Name AALN/S0/SU0/0 at TransitGW2801.mydomain.local 

Product Cisco MGCP FXO Port 
Gateway TransitGW2801.mydomain.local 
Device Protocol Analog Access 
Registration Registered with Cisco Unified Communications Manager 192.168.200.6 
IP Address 192.168.XXX.252 
End-Point Name AALN/S0/SU0/1 at TransitGW2801.mydomain.local 



Everything is identical in the CCM (UCM 6.01) 
both ports are configured EXACTLY the same way... 



What the heck is going on? 


more info: 


Config on the router: 
voice-port 0/0/0 
supervisory disconnect dualtone mid-call 
echo-cancel coverage 32 
timeouts call-disconnect 5 
timeouts wait-release 5 
timing hookflash-out 50 
! 
voice-port 0/0/1 
supervisory disconnect dualtone mid-call 
echo-cancel coverage 32 
timeouts call-disconnect 5 
timeouts wait-release 5 
timing hookflash-out 50 
! 
ccm-manager switchback immediate 
ccm-manager fallback-mgcp 
ccm-manager redundant-host 192.168.200.2 
ccm-manager mgcp 
no ccm-manager fax protocol cisco 
ccm-manager music-on-hold 
ccm-manager config server 192.168.200.2 
! 
mgcp 
mgcp call-agent 192.168.200.6 service-type mgcp version 0.1 
mgcp dtmf-relay voip codec all mode out-of-band 
mgcp rtp unreachable timeout 1000 action notify 
mgcp modem passthrough voip mode nse 
mgcp package-capability rtp-package 
no mgcp package-capability res-package 
mgcp package-capability sst-package 
no mgcp package-capability fxr-package 
no mgcp timer receive-rtcp 
mgcp sdp simple 
mgcp fax t38 inhibit 
mgcp rtp payload-type g726r16 static 
mgcp bind control source-interface FastEthernet0/0 
mgcp bind media source-interface FastEthernet0/0 
! 
mgcp profile default 



dial-peer voice 99900 pots 
service mgcpapp 
port 0/0/1 
! 
dial-peer voice 99901 pots 
service mgcpapp 
port 0/0/1 
! 
dial-peer voice 2000 voip 
incoming called-number . 
dtmf-relay h245-alphanumeric 
codec g711ulaw 
no vad 

Running: c2801-spservicesk9-mz.124-9.T7.bin 

TransitGW2801#sh mgcp endpoint 
aaln/S0/SU0/1 at TransitGW2801 


That output should ALSO show 
aaln/S0/SU0/0 at TransitGW2801 

and would show it, I think, if the port registered. 



TransitGW2801#sh voice port summary 
IN OUT 
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC 
============== == ============ ===== ==== ======== ======== == 
0/0/0 -- fxo-ls up dorm idle on-hook y 
0/0/1 -- fxo-ls up dorm idle on-hook y 

TransitGW2801#sh mgcp statistics 
UDP pkts rx 828, tx 828 
Unrecognized rx pkts 0, MGCP message parsing errors 0 
Duplicate MGCP ack tx 0, Invalid versions count 0 
CreateConn rx 5, successful 0, failed 5 
DeleteConn rx 5, successful 5, failed 0 
ModifyConn rx 0, successful 0, failed 0 
DeleteConn tx 0, successful 0, failed 0 
NotifyRequest rx 12, successful 11, failed 1 
AuditConnection rx 0, successful 0, failed 0 
AuditEndpoint rx 1, successful 1, failed 0 
RestartInProgress tx 1, successful 1, failed 0 
Notify tx 804, successful 804, failed 0 
ACK tx 17, NACK tx 6 
ACK rx 805, NACK rx 0 

IP address based Call Agents statistics: 
IP address 192.168.200.6, Total msg rx 828, 
successful 822, failed 6 
System resource check is DISABLED. No available statistic 

DS0 Resource Statistics 
----------------------- 
Utilization: 0.00 percent 
Total channels: 1 < This would appear to just confirm the fact that only one port registered, not be a source of the problem 
Addressable channels: 1 
Inuse channels: 0 
Disabled channels: 0 
Free channels: 1 


## Both ports exist--- both are admin UP, with no failures, both are Loop Start 
So it's not something confused with the hardware. 


TransitGW2801#sh voice port 

Foreign Exchange Office 0/0/0 Slot is 0, Sub-unit is 0, Port is 0 
Type of VoicePort is FXO 
Operation State is DORMANT 
Administrative State is UP 
No Interface Down Failure 
Description is not set 
Noise Regeneration is enabled 
Non Linear Processing is enabled 
Non Linear Mute is disabled 
Non Linear Threshold is -21 dB 
Music On Hold Threshold is Set to -38 dBm 
In Gain is Set to 0 dB 
Out Attenuation is Set to 3 dB 
Echo Cancellation is enabled 
Echo Cancellation NLP mute is disabled 
Echo Cancellation NLP threshold is -21 dB 
Echo Cancel Coverage is set to 32 ms 
Echo Cancel worst case ERL is set to 6 dB 
Playout-delay Mode is set to adaptive 
Playout-delay Nominal is set to 60 ms 
Playout-delay Maximum is set to 250 ms 
Playout-delay Minimum mode is set to default, value 40 ms 
Playout-delay Fax is set to 300 ms 
Connection Mode is normal 
Connection Number is not set 
Initial Time Out is set to 10 s 
Interdigit Time Out is set to 10 s 
Call Disconnect Time Out is set to 5 s 
Ringing Time Out is set to 180 s 
Wait Release Time Out is set to 5 s 
Companding Type is u-law 
Region Tone is set for US 

Analog Info Follows: 
Currently processing none 
Maintenance Mode Set to None (not in mtc mode) 
Number of signaling protocol errors are 0 
Impedance is set to 600r Ohm 
Station name None, Station number None 
Translation profile (Incoming): 
Translation profile (Outgoing): 

Voice card specific Info Follows: 
Signal Type is loopStart 
Battery-Reversal is enabled 
Number Of Rings is set to 1 
Supervisory Disconnect is dualtone mid-call 
Answer Supervision is inactive 
Hook Status is On Hook 
Ring Detect Status is inactive 
Ring Ground Status is inactive 
Tip Ground Status is inactive 
Dial Out Type is dtmf 
Digit Duration Timing is set to 100 ms 
InterDigit Duration Timing is set to 100 ms 
Pulse Rate Timing is set to 10 pulses/second 
InterDigit Pulse Duration Timing is set to 750 ms 
Percent Break of Pulse is 60 percent 
GuardOut timer is 2000 ms 
Minimum ring duration timer is 125 ms 
Hookflash-in Timing is set to 600 ms 
Hookflash-out Timing is set to 50 ms 
Supervisory Disconnnct Timing is set to 350 ms 
OPX Ring Wait Timing is set to 6000 ms 

Foreign Exchange Office 0/0/1 Slot is 0, Sub-unit is 0, Port is 1 
Type of VoicePort is FXO 
Operation State is DORMANT 
Administrative State is UP 
No Interface Down Failure 
Description is not set 
Noise Regeneration is enabled 
Non Linear Processing is enabled 
Non Linear Mute is disabled 
Non Linear Threshold is -21 dB 
Music On Hold Threshold is Set to -38 dBm 
In Gain is Set to 0 dB 
Out Attenuation is Set to 3 dB 
Echo Cancellation is enabled 
Echo Cancellation NLP mute is disabled 
Echo Cancellation NLP threshold is -21 dB 
Echo Cancel Coverage is set to 32 ms 
Echo Cancel worst case ERL is set to 6 dB 
Playout-delay Mode is set to adaptive 
Playout-delay Nominal is set to 60 ms 
Playout-delay Maximum is set to 250 ms 
Playout-delay Minimum mode is set to default, value 40 ms 
Playout-delay Fax is set to 300 ms 
Connection Mode is normal 
Connection Number is not set 
Initial Time Out is set to 10 s 
Interdigit Time Out is set to 10 s 
Call Disconnect Time Out is set to 5 s 
Ringing Time Out is set to 180 s 
Wait Release Time Out is set to 5 s 
Companding Type is u-law 
Region Tone is set for US 

Analog Info Follows: 
Currently processing none 
Maintenance Mode Set to None (not in mtc mode) 
Number of signaling protocol errors are 0 
Impedance is set to 600r Ohm 
Station name None, Station number None 
Translation profile (Incoming): 
Translation profile (Outgoing): 

Voice card specific Info Follows: 
Signal Type is loopStart 
Battery-Reversal is enabled 
Number Of Rings is set to 1 
Supervisory Disconnect is dualtone mid-call 
Answer Supervision is inactive 
Hook Status is On Hook 
Ring Detect Status is inactive 
Ring Ground Status is inactive 
Tip Ground Status is inactive 
Dial Out Type is dtmf 
Digit Duration Timing is set to 100 ms 
InterDigit Duration Timing is set to 100 ms 
Pulse Rate Timing is set to 10 pulses/second 
InterDigit Pulse Duration Timing is set to 750 ms 
Percent Break of Pulse is 60 percent 
GuardOut timer is 2000 ms 
Minimum ring duration timer is 125 ms 
Hookflash-in Timing is set to 600 ms 
Hookflash-out Timing is set to 50 ms 
Supervisory Disconnnct Timing is set to 350 ms 
OPX Ring Wait Timing is set to 6000 ms 



Tim Reimers 
Systems Analyst II 
Information Technology Services 
City of Asheville 
70 Court Plaza 
Asheville, NC 28801 
phone - 828-259-5512 
treimers at ashevillenc.gov 

_______________________________________________ cisco-voip mailing list cisco-voip at puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-voip 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20090213/0f93ef10/attachment.html>


More information about the cisco-voip mailing list