[cisco-voip] Calling Name Issue with Nortel 11c and 61c with QSIG

[Nate VanMaren]

Is there a Cisco Communications Manager controling the voicegateways?  H.323 support for QSIG is very very limited, you need to run the gateways with MGCP, and you'll get much better results with QSIG.

-Nate
________________________________
From: cisco-voip-bounces at puck.nether.net [cisco-voip-bounces at puck.nether.net] On Behalf Of Syed Khalid Ali [syed.khalid.khursheed at gmail.com]
Sent: Sunday, November 01, 2009 1:39 AM
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] Calling Name Issue with Nortel 11c and 61c with QSIG

Greeting:

I have the following scenario. Two PBXes 11c and 61c. Both connected with Cisco Voice gateways as following:
11c----------------E1----------------VG1----------------VG2----------------61c
Calls are working fine but I could not able to get the Caller Name at each site. Both PBXes are acting the ISDN network side but QSIG.

11c has extension of 12XX and
61c has 2XXX, 3XXX, 4XXX

After looking at the command reference, I concluded that following commands should work:
isdn supp-service name calling
isdn outgoing display-ie

I did the following config on both sides:
interface Serial0/3/0:15
 no ip address
 no logging event link-status
 isdn switch-type primary-qsig
 isdn incoming-voice voice
 isdn supp-service name calling
 isdn send-alerting
 isdn sending-complete
 isdn outgoing display-ie
 no cdp enable

but I am getting the following error message in Q931 debugs:
ISDN Se0/3/0:15 Q931: Applying typeplan for sw-type 0x16 is 0x0 0x1, Calling num
 1216
ISDN Se0/3/0:15 Q931: Applying typeplan for sw-type 0x16 is 0x0 0x9, Called num
0302
ISDN Se0/3/0:15 Q931: TX -> SETUP pd = 8  callref = 0x071A
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA9839F
                Exclusive, Channel 31
        Progress Ind i = 0x8183 - Origination address is non-ISDN
        Calling Party Number i = 0x0180, '1216'
                Plan:ISDN, Type:Unknown
        Called Party Number i = 0x89, '0302'
                Plan:Private, Type:Unknown
        Locking Shift to Codeset 5
        Codeset 5 IE 0x31  i = 0x80
        Codeset 5 IE 0x32  i = 0x81
ISDN Se0/3/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x871A
        Channel ID i = 0xA9839F
                Exclusive, Channel 31
ISDN Se0/3/0:15 Q931: RX <- ALERTING pd = 8  callref = 0x871A
        Locking Shift to Codeset 5
        Codeset 5 IE 0x32  i = 0x81

 ISDN Se0/3/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x071A
        Cause i = 0x8090 - Normal call clearing
ISDN Se0/3/0:15 Q931: RX <- CONNECT pd = 8  callref = 0x871A
        Progress Ind i = 0x8182 - Destination address is non-ISDN
        Connected Number i = 0x0080, '4446'
        Locking Shift to Codeset 5
        Codeset 5 IE 0x32  i = 0x81
ISDN Se0/3/0:15 **ERROR**: Ux_BadMsg: Invalid Message for call state 11, call id
 0x8E1D, call ref 0x71A, event 0x7
ISDN Se0/3/0:15 Q931: TX -> STATUS pd = 8  callref = 0x071A
        Cause i = 0x80E507 - Message not compatible with call state
        Call State i = 0x0B
ISDN Se0/3/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x871A
ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x071A

--
Thanks,
Syed Khalid Ali


 NOTICE: This email message is for the sole use of the intended recipient(s) and may contain confidential and privileged information. Any unauthorized review, use, disclosure or distribution is prohibited. If you are not the intended recipient, please contact the sender by reply email and destroy all copies of the original message.


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20091101/6c803e10/attachment.html>