[cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID card

[Lelio Fulgenzi]

hmmm. works. I basically copied over my VG224 config and plugged in the MAC of gi0/0 and it works. 

now, is it supported? ;) 




vgw-jnhn-a#show stcapp device summary 
Total Devices: 1 
Total Calls in Progress: 0 
Total Call Legs in Use: 0 

Port Device Device Call Dev Directory Dev 
Identifier Name State State Type Number Cntl 
---------- --------------- -------- ------------- ------- ----------- ---- 
0/1/0 AN254530DA80080 IS IDLE ALG 57001 CCM 



! 
interface Loopback104 
description Voice Network Loopback (SRST/Misc) 
ip address 10.104.13.201 255.255.255.255 
h323-gateway voip bind srcaddr 10.104.13.201 
! 
stcapp ccm-group 105 
stcapp 
! 
voice-port 0/1/0 <this section was filled in automatically> 
timeouts ringing infinity 
station-id number 57001 </end> 
! 
sccp local Loopback104 
sccp ccm 10.104.91.105 identifier 105 version 7.0 
sccp ccm 10.104.13.86 identifier 1386 version 7.0 
sccp ccm 10.104.13.201 identifier 13201 version 7.0 
sccp ccm 10.104.13.202 identifier 13202 version 7.0 
sccp 
! 
sccp ccm group 105 
associate ccm 105 priority 1 
associate ccm 1386 priority 2 
! 


--- 
Lelio Fulgenzi, B.A. 
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1 
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN) 
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
Cooking with unix is easy. You just sed it and forget it. 
- LFJ (with apologies to Mr. Popeil) 


----- Original Message ----- 
From: "Bill" <bill at hitechconnection.net> 
To: "Lelio Fulgenzi" <lelio at uoguelph.ca> 
Cc: "cisco-voip voyp list" <cisco-voip at puck.nether.net> 
Sent: Friday, April 23, 2010 11:34:55 AM GMT -05:00 US/Canada Eastern 
Subject: RE: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID card 




I don’t think you can use a loopback for this. If I remember right this is the same as setting up a transcoder / conference bridge resource and you have to use a physical adaptor. 






From: Lelio Fulgenzi [mailto:lelio at uoguelph.ca] 
Sent: Friday, April 23, 2010 10:30 AM 
To: Bill 
Cc: cisco-voip voyp list 
Subject: Re: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID card 




hmmm, i'm going to be using a loopback address. 



--- 
Lelio Fulgenzi, B.A. 
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1 
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN) 
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
Cooking with unix is easy. You just sed it and forget it. 
- LFJ (with apologies to Mr. Popeil) 


----- Original Message ----- 
From: "Bill" <bill at hitechconnection.net> 
To: "Lelio Fulgenzi" <lelio at uoguelph.ca>, "cisco-voip voyp list" <cisco-voip at puck.nether.net> 
Sent: Friday, April 23, 2010 11:20:45 AM GMT -05:00 US/Canada Eastern 
Subject: RE: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID card 

The MAC address you configure for SCCP traffic to bind to. 



sccp local gigabitEthernet 0/0 










From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Lelio Fulgenzi 
Sent: Friday, April 23, 2010 10:15 AM 
To: cisco-voip voyp list 
Subject: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID card 




OK, silly question, what MAC address do I use when configuring a VIC3-2FXS-E/DID with SCCP? 

Is it similar to a VG248 where I use the MAC address of fas0/0? 

So on a 3900, I would use the MAC address of GigabitEthernet0/0 ? 

I'll try that and see how it goes. 


--- 
Lelio Fulgenzi, B.A. 
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1 
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN) 
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
Cooking with unix is easy. You just sed it and forget it. 
- LFJ (with apologies to Mr. Popeil)
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100423/a4869d6f/attachment.html>