[cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DIDcard

[Nick Matthews]

That's from the old days when you used the MAC address in the
registration name of the device.  Now you simply put the name in the
'associate profile x register <NAME>' command.  The NAME historically
was mac based but is no longer required to be in that naming
convention.

-nick

On Mon, Apr 26, 2010 at 8:59 AM, Lelio Fulgenzi <lelio at uoguelph.ca> wrote:
> Thanks for clearing that up Bill. I think some of us (definitely me) read
> that a bit quicker than we should have. It's also helpful to know you need a
> physical address for transcoder/CFB configuration.
>
> Now, do you mean physical IP address?
>
> ---
> Lelio Fulgenzi, B.A.
> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> Cooking with unix is easy. You just sed it and forget it.
>                               - LFJ (with apologies to Mr. Popeil)
>
>
> ----- Original Message -----
> From: "Bill" <bill at hitechconnection.net>
> To: "Dschulz" <dschulz at skyline-ats.com>, "Peter Slow" <peter.slow at gmail.com>
> Cc: "cisco-voip voyp list" <cisco-voip at puck.nether.net>
> Sent: Monday, April 26, 2010 7:58:45 AM GMT -05:00 US/Canada Eastern
> Subject: Re: [cisco-voip] MAC address for SCCP controlled
> VIC3-2FXS-E/DIDcard
>
> I didn't say you couldn't use it in you sccp bind statement. I said you
> couldn't use it for a transcoder / CFB configuration.
>
> -----Original Message-----
> From: Dschulz [mailto:dschulz at skyline-ats.com]
> Sent: Sunday, April 25, 2010 8:56 PM
> To: Peter Slow; Bill
> Cc: cisco-voip voyp list
> Subject: RE: [cisco-voip] MAC address for SCCP controlled
> VIC3-2FXS-E/DIDcard
>
> The loopback can be used and is preferable to use it. However, you need to
> make sure it is included in your routing table.
>
> Dave
>
>
> -----Original Message-----
> From: Peter Slow <peter.slow at gmail.com>
> Sent: Sunday, April 25, 2010 5:32 PM
> To: Bill <bill at hitechconnection.net>
> Cc: cisco-voip voyp list <cisco-voip at puck.nether.net>
> Subject: Re: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID
> card
>
> Since when can't you use a loopback interface is your SCCP bind
> interface? I'm not aware of that limitation.
>
> -Peter
>
> On Fri, Apr 23, 2010 at 11:34 AM, Bill <bill at hitechconnection.net> wrote:
>> I don't think you can use a loopback for this. If I remember right this is
>> the same as setting up a transcoder / conference bridge resource and you
>> have to use a physical adaptor.
>>
>>
>>
>> ________________________________
>>
>> From: Lelio Fulgenzi [mailto:lelio at uoguelph.ca]
>> Sent: Friday, April 23, 2010 10:30 AM
>> To: Bill
>> Cc: cisco-voip voyp list
>> Subject: Re: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID
>> card
>>
>>
>>
>> hmmm, i'm going to be using a loopback address.
>>
>
>
> [The entire original message is not included]
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>