[cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DIDcard

[Lelio Fulgenzi]

Thanks for clearing that up Bill. I think some of us (definitely me) read that a bit quicker than we should have. It's also helpful to know you need a physical address for transcoder/CFB configuration. 

Now, do you mean physical IP address? 

--- 
Lelio Fulgenzi, B.A. 
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1 
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN) 
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
Cooking with unix is easy. You just sed it and forget it. 
- LFJ (with apologies to Mr. Popeil) 


----- Original Message ----- 
From: "Bill" <bill at hitechconnection.net> 
To: "Dschulz" <dschulz at skyline-ats.com>, "Peter Slow" <peter.slow at gmail.com> 
Cc: "cisco-voip voyp list" <cisco-voip at puck.nether.net> 
Sent: Monday, April 26, 2010 7:58:45 AM GMT -05:00 US/Canada Eastern 
Subject: Re: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DIDcard 

I didn't say you couldn't use it in you sccp bind statement. I said you 
couldn't use it for a transcoder / CFB configuration. 

-----Original Message----- 
From: Dschulz [mailto:dschulz at skyline-ats.com] 
Sent: Sunday, April 25, 2010 8:56 PM 
To: Peter Slow; Bill 
Cc: cisco-voip voyp list 
Subject: RE: [cisco-voip] MAC address for SCCP controlled 
VIC3-2FXS-E/DIDcard 

The loopback can be used and is preferable to use it. However, you need to 
make sure it is included in your routing table. 

Dave 


-----Original Message----- 
From: Peter Slow <peter.slow at gmail.com> 
Sent: Sunday, April 25, 2010 5:32 PM 
To: Bill <bill at hitechconnection.net> 
Cc: cisco-voip voyp list <cisco-voip at puck.nether.net> 
Subject: Re: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID 
card 

Since when can't you use a loopback interface is your SCCP bind 
interface? I'm not aware of that limitation. 

-Peter 

On Fri, Apr 23, 2010 at 11:34 AM, Bill <bill at hitechconnection.net> wrote: 
> I don't think you can use a loopback for this. If I remember right this is 
> the same as setting up a transcoder / conference bridge resource and you 
> have to use a physical adaptor. 
> 
> 
> 
> ________________________________ 
> 
> From: Lelio Fulgenzi [mailto:lelio at uoguelph.ca] 
> Sent: Friday, April 23, 2010 10:30 AM 
> To: Bill 
> Cc: cisco-voip voyp list 
> Subject: Re: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID 
> card 
> 
> 
> 
> hmmm, i'm going to be using a loopback address. 
> 


[The entire original message is not included] 

_______________________________________________ 
cisco-voip mailing list 
cisco-voip at puck.nether.net 
https://puck.nether.net/mailman/listinfo/cisco-voip 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100426/1629bf9f/attachment.html>