[cisco-voip] Configure incoming CLID on isdn of a 2821

[Paul]

Did Matt's post help you at all?

http://www.blindhog.net/cisco-caller-id-name-support-for-h323-facility-ie/




________________________________
From:"Leetun, Rob" <rleetun at bouldercounty.org>
To:"Leetun, Rob" <rleetun at bouldercounty.org>; cisco-voip at puck.nether.net
Cc:"Barger, Joe" <jbarger at bouldercounty.org>; Paul <asobihoudai at yahoo.com>
Sent: Wed, April 28, 2010 11:32:37 AM
Subject: RE: [cisco-voip] Configure incoming CLID on isdn of a 2821


Here is the Debug isdn q931
 
Apr 28 12:14:43.243: ISDN Se0/2/0:23 Q931: RX <- SETUP pd =
8  callref = 0x001B 
        Bearer Capability i =
0x8090A2 
               
Standard = CCITT 
               
Transfer Capability = Speech  
               
Transfer Mode = Circuit 
               
Transfer Rate = 64 kbit/s 
        Channel ID i =
0xA98397 
               
Exclusive, Channel 23 
        Facility i =
0x9FAA068001008201008B0100A11802011C0201008210416E64726561204672616E636973636F 
               
Protocol Profile =  Networking Extensions 
               
0x0100 
               
0x820100 
               
0x8B0100 
               
0xA11802011C0201008210416E64726561204672616E636973636F 
               
Component = Invoke component 
        Calling Party
Number i = 0x00A0, '4718' 
               
Plan:Unknown, Type:Unknown 
        Called Party Number i
= 0x80, '3579' 
               
Plan:Unknown, Type:Unknown
Apr 28 12:14:43.259: ISDN Se0/2/0:23 Q931: TX -> CALL_PROC pd
= 8  callref = 0x801B 
        Channel ID i =
0xA98397 
               
Exclusive, Channel 23
Apr 28 12:14:43.395: ISDN Se0/2/0:23 Q931: TX -> ALERTING pd
= 8  callref = 0x801B 
        Progress Ind i =
0x8188 - In-band info or appropriate now available 
Apr 28 12:14:47.907: %ISDN-6-CONNECT: Interface Serial0/2/0:22
is now connected to 4718 N/A
Apr 28 12:14:47.907: %ISDN-6-CONNECT: Interface Serial0/2/0:22
is now connected to 4718 N/A
Apr 28 12:14:47.907: ISDN Se0/2/0:23 Q931: TX -> CONNECT pd =
8  callref = 0x801B
Apr 28 12:14:47.923: ISDN Se0/2/0:23 Q931: RX <- CONNECT_ACK
pd = 8  callref = 0x001B
Apr 28 12:14:56.051: ISDN Se0/2/0:23 Q931: RX <- DISCONNECT
pd = 8  callref = 0x001B 
        Cause i = 0x8090 -
Normal call clearing
Apr 28 12:14:56.051: %ISDN-6-DISCONNECT: Interface
Serial0/2/0:22  disconnected from 4718 , call lasted 8 seconds
Apr 28 12:14:56.055: ISDN Se0/2/0:23 Q931: TX -> RELEASE pd =
8  callref = 0x801B
Apr 28 12:14:56.067: ISDN Se0/2/0:23 Q931: RX <- RELEASE_COMP
pd = 8  callref = 0x001B
 
 
From:cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On
Behalf Of Leetun, Rob
Sent: Wednesday, April 28, 2010 11:41 AM
To:cisco-voip at puck.nether.net
Subject: [cisco-voip] Configure incoming CLID on isdn of a 2821
 
Hi,
 
I
cannot get incoming CLID to be presented on the phone.  We have a 2821
with isdn.  Does anyone know of a command I can use to get this to work?
 
Thanks!
 
 
Rob
 
Robert
Leetun
Network
Engineer
Boulder
County Information Technology
2025
14th Street
Boulder,
CO 80302
303
441-3866 (W)
303
441-3983 (F)
rleetun at bouldercounty.org