[cisco-voip] Configure incoming CLID on isdn of a 2821

[Ryan Ratliff]

So your name is in the facility.  You need to check out the CCM traces where the full thing will be decoded and you can see what number is there.

-Ryan

On Apr 28, 2010, at 5:25 PM, Barger, Joe wrote:

> Yeah that is the weird part we are seeing the name even though you don’t see it incoming  in the debug…
>  
> From: Ryan Ratliff [mailto:rratliff at cisco.com] 
> Sent: Wednesday, April 28, 2010 2:48 PM
> To: Matthew Loraditch
> Cc: Leetun, Rob; cisco-voip at puck.nether.net; Barger, Joe
> Subject: Re: [cisco-voip] Configure incoming CLID on isdn of a 2821
>  
> I believe if there is a number in the facility it will override that in the calling number IE.  You can look at CCM traces to see if we are decoding the facility.
>  
> -Ryan
>  
> On Apr 28, 2010, at 4:14 PM, Matthew Loraditch wrote:
> 
> 
> Well you aren’t getting calling name and the number you are getting appears to be private, is this a telco pri or a private link?  albeit regardless you should be getting the number to come through to the phones unless you have something in CCM or your dial-peers altering it.
>  
>  
> Matthew Loraditch, CCNA, CCDA
> 1965 Greenspring Drive
> Timonium, MD 21093 
> support at heliontechnologies.com
> (p) (410) 252-8830
> (F) (443) 541-1593
> 
> Visit us at www.heliontechnologies.com 
> Support Issue? Email support at heliontechnologies.com for fast assistance!
>  
> From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Leetun, Rob
> Sent: Wednesday, April 28, 2010 2:33 PM
> To: Leetun, Rob; cisco-voip at puck.nether.net
> Cc: Barger, Joe
> Subject: Re: [cisco-voip] Configure incoming CLID on isdn of a 2821
>  
> Here is the Debug isdn q931
>  
> Apr 28 12:14:43.243: ISDN Se0/2/0:23 Q931: RX <- SETUP pd = 8  callref = 0x001B
>         Bearer Capability i = 0x8090A2
>                 Standard = CCITT
>                 Transfer Capability = Speech 
>                 Transfer Mode = Circuit
>                 Transfer Rate = 64 kbit/s
>         Channel ID i = 0xA98397
>                 Exclusive, Channel 23
>         Facility i = 0x9FAA068001008201008B0100A11802011C0201008210416E64726561204672616E636973636F
>                 Protocol Profile =  Networking Extensions
>                 0x0100
>                 0x820100
>                 0x8B0100
>                 0xA11802011C0201008210416E64726561204672616E636973636F
>                 Component = Invoke component
>         Calling Party Number i = 0x00A0, '4718'
>                 Plan:Unknown, Type:Unknown
>         Called Party Number i = 0x80, '3579'
>                 Plan:Unknown, Type:Unknown
> Apr 28 12:14:43.259: ISDN Se0/2/0:23 Q931: TX -> CALL_PROC pd = 8  callref = 0x801B
>         Channel ID i = 0xA98397
>                 Exclusive, Channel 23
> Apr 28 12:14:43.395: ISDN Se0/2/0:23 Q931: TX -> ALERTING pd = 8  callref = 0x801B
>         Progress Ind i = 0x8188 - In-band info or appropriate now available
> Apr 28 12:14:47.907: %ISDN-6-CONNECT: Interface Serial0/2/0:22 is now connected to 4718 N/A
> Apr 28 12:14:47.907: %ISDN-6-CONNECT: Interface Serial0/2/0:22 is now connected to 4718 N/A
> Apr 28 12:14:47.907: ISDN Se0/2/0:23 Q931: TX -> CONNECT pd = 8  callref = 0x801B
> Apr 28 12:14:47.923: ISDN Se0/2/0:23 Q931: RX <- CONNECT_ACK pd = 8  callref = 0x001B
> Apr 28 12:14:56.051: ISDN Se0/2/0:23 Q931: RX <- DISCONNECT pd = 8  callref = 0x001B
>         Cause i = 0x8090 - Normal call clearing
> Apr 28 12:14:56.051: %ISDN-6-DISCONNECT: Interface Serial0/2/0:22  disconnected from 4718 , call lasted 8 seconds
> Apr 28 12:14:56.055: ISDN Se0/2/0:23 Q931: TX -> RELEASE pd = 8  callref = 0x801B
> Apr 28 12:14:56.067: ISDN Se0/2/0:23 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x001B
>  
>  
> From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Leetun, Rob
> Sent: Wednesday, April 28, 2010 11:41 AM
> To: cisco-voip at puck.nether.net
> Subject: [cisco-voip] Configure incoming CLID on isdn of a 2821
>  
> Hi,
>  
> I cannot get incoming CLID to be presented on the phone.  We have a 2821 with isdn.  Does anyone know of a command I can use to get this to work?
>  
> Thanks!
>  
>  
> Rob
>  
> Robert Leetun
> Network Engineer
> Boulder County Information Technology
> 2025 14th Street
> Boulder, CO 80302
> 303 441-3866 (W)
> 303 441-3983 (F)
> rleetun at bouldercounty.org
>  
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>  

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100428/eed6cec7/attachment.html>