[cisco-voip] Upgrade from 2801 to 2911

[Burak Dag]

Hi,

can you check the region on ccm and the codecs??

Thanks



2010/8/9 Guilherme Loch Waltrick Góes <glwgoes at gmail.com>

> Hi guys,
>
> We just upgraded a site that was running a 2801 with a ISDN PRI link
> to a PBX to a 2911 with the exact same setup. The setup with the 2801
> was running just fine. The problem is, running with the same config on
> the 2911 we keep getting MANY Line Code Violations and other assorted
> errors, the calls are very noisy and sometimes we can't place the
> calls from this site to the other sites.
>
> Did anyone experienced the same situation? How can a solve this problem?
>
> Bellow is some info about this router:
>
> #sh controllers e1 0/1/0
> E1 0/1/0 is up.
>  Applique type is Channelized E1 - balanced
>  Description: Enlace E1 com o PABX
>  No alarms detected.
>  alarm-trigger is not set
>  Version info Firmware: 20090408, FPGA: 13, spm_count = 0
>  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Internal.
>  Data in current interval (38 seconds elapsed):
>     20724 Line Code Violations, 170 Path Code Violations
>     1 Slip Secs, 0 Fr Loss Secs, 38 Line Err Secs, 0 Degraded Mins
>     38 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
>  Data in Interval 1:
>     415943 Line Code Violations, 4586 Path Code Violations
>     6 Slip Secs, 0 Fr Loss Secs, 900 Line Err Secs, 15 Degraded Mins
>     900 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
> Secs
>  Total Data (last 1 15 minute intervals):
>     415943 Line Code Violations, 4586 Path Code Violations,
>     6 Slip Secs, 0 Fr Loss Secs, 900 Line Err Secs, 15 Degraded Mins,
>     900 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
> Secs
>
> #sh ver
> Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version
> 15.0(1)M1, RELEASE SOFTWARE (fc1)
>
> #sh run
> -- some output ommited --
> network-clock-participate wic 1
>
> isdn switch-type primary-qsig
> isdn gateway-max-interworking
>
> voice-card 0
>  dsp services dspfarm
> !
> !
> !
> voice class codec 1
>  codec preference 1 g729br8
>  codec preference 2 g729r8
> !
> !
> controller E1 0/1/0
>  framing NO-CRC4
>  clock source internal
>  pri-group timeslots 1-12,16
>  description Enlace E1 com o PABX
> !
> interface GigabitEthernet0/0
>  description LAN
>  bandwidth 1000000
>  ip address 172.26.130.2 255.255.255.192
>  ip wccp 61 redirect in
>  ip flow ingress
>  ip flow egress
>  duplex auto
>  speed auto
>  h323-gateway voip interface
>  h323-gateway voip id GK_SEDE_1 ipaddr 172.254.1.3 1719
>  h323-gateway voip id GK_SEDE_2 ipaddr 172.254.1.2 1719
>  h323-gateway voip h323-id GW_XXXX
>  h323-gateway voip tech-prefix 1#
>  h323-gateway voip bind srcaddr 172.26.130.2
>  service-policy input MARKQoSOUT
>
> !
> interface Serial0/1/0:15
>  no ip address
>  encapsulation hdlc
>  isdn switch-type primary-qsig
>  isdn overlap-receiving
>  isdn incoming-voice voice
>  isdn contiguous-bchan
>  no cdp enable
> !
> voice-port 0/1/0:15
>  cptone BR
> !
> dial-peer voice 5 pots
>  description Internal Extensions to the PBX
>  destination-pattern 3396....
>  direct-inward-dial
>  port 0/1/0:15
>  forward-digits 4
>  no register e164
> !
> dial-peer voice 13 voip
>  description Output dial-peer
>  destination-pattern 3.......
>  session target ras
>  voice-class codec 1
> !
> !
> gateway
> !
> !
> !
> gatekeeper
>  shutdown
>
> Guilherme Loch Góes
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100809/963d345f/attachment.html>