[cisco-voip] Upgrade from 2801 to 2911

[Guilherme Loch Waltrick Góes]

It's a simple voice gateway, there is no CCM.

I'll try to upgrade to 15.0M3 and will report the status.

Thanks for your help.

Regards,

Guilherme Loch Góes




On Mon, Aug 9, 2010 at 11:11 AM, Burak Dag <burdag at gmail.com> wrote:
> Hi,
>
> can you check the region on ccm and the codecs??
>
> Thanks
>
>
> 2010/8/9 Guilherme Loch Waltrick Góes <glwgoes at gmail.com>
>>
>> Hi guys,
>>
>> We just upgraded a site that was running a 2801 with a ISDN PRI link
>> to a PBX to a 2911 with the exact same setup. The setup with the 2801
>> was running just fine. The problem is, running with the same config on
>> the 2911 we keep getting MANY Line Code Violations and other assorted
>> errors, the calls are very noisy and sometimes we can't place the
>> calls from this site to the other sites.
>>
>> Did anyone experienced the same situation? How can a solve this problem?
>>
>> Bellow is some info about this router:
>>
>> #sh controllers e1 0/1/0
>> E1 0/1/0 is up.
>>  Applique type is Channelized E1 - balanced
>>  Description: Enlace E1 com o PABX
>>  No alarms detected.
>>  alarm-trigger is not set
>>  Version info Firmware: 20090408, FPGA: 13, spm_count = 0
>>  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Internal.
>>  Data in current interval (38 seconds elapsed):
>>     20724 Line Code Violations, 170 Path Code Violations
>>     1 Slip Secs, 0 Fr Loss Secs, 38 Line Err Secs, 0 Degraded Mins
>>     38 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
>> Secs
>>  Data in Interval 1:
>>     415943 Line Code Violations, 4586 Path Code Violations
>>     6 Slip Secs, 0 Fr Loss Secs, 900 Line Err Secs, 15 Degraded Mins
>>     900 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
>> Secs
>>  Total Data (last 1 15 minute intervals):
>>     415943 Line Code Violations, 4586 Path Code Violations,
>>     6 Slip Secs, 0 Fr Loss Secs, 900 Line Err Secs, 15 Degraded Mins,
>>     900 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
>> Secs
>>
>> #sh ver
>> Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version
>> 15.0(1)M1, RELEASE SOFTWARE (fc1)
>>
>> #sh run
>> -- some output ommited --
>> network-clock-participate wic 1
>>
>> isdn switch-type primary-qsig
>> isdn gateway-max-interworking
>>
>> voice-card 0
>>  dsp services dspfarm
>> !
>> !
>> !
>> voice class codec 1
>>  codec preference 1 g729br8
>>  codec preference 2 g729r8
>> !
>> !
>> controller E1 0/1/0
>>  framing NO-CRC4
>>  clock source internal
>>  pri-group timeslots 1-12,16
>>  description Enlace E1 com o PABX
>> !
>> interface GigabitEthernet0/0
>>  description LAN
>>  bandwidth 1000000
>>  ip address 172.26.130.2 255.255.255.192
>>  ip wccp 61 redirect in
>>  ip flow ingress
>>  ip flow egress
>>  duplex auto
>>  speed auto
>>  h323-gateway voip interface
>>  h323-gateway voip id GK_SEDE_1 ipaddr 172.254.1.3 1719
>>  h323-gateway voip id GK_SEDE_2 ipaddr 172.254.1.2 1719
>>  h323-gateway voip h323-id GW_XXXX
>>  h323-gateway voip tech-prefix 1#
>>  h323-gateway voip bind srcaddr 172.26.130.2
>>  service-policy input MARKQoSOUT
>>
>> !
>> interface Serial0/1/0:15
>>  no ip address
>>  encapsulation hdlc
>>  isdn switch-type primary-qsig
>>  isdn overlap-receiving
>>  isdn incoming-voice voice
>>  isdn contiguous-bchan
>>  no cdp enable
>> !
>> voice-port 0/1/0:15
>>  cptone BR
>> !
>> dial-peer voice 5 pots
>>  description Internal Extensions to the PBX
>>  destination-pattern 3396....
>>  direct-inward-dial
>>  port 0/1/0:15
>>  forward-digits 4
>>  no register e164
>> !
>> dial-peer voice 13 voip
>>  description Output dial-peer
>>  destination-pattern 3.......
>>  session target ras
>>  voice-class codec 1
>> !
>> !
>> gateway
>> !
>> !
>> !
>> gatekeeper
>>  shutdown
>>
>> Guilherme Loch Góes
>>
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>