[cisco-voip] 3845 DSP

Tue Feb 9 17:14:18 EST 2010

i'm curious about what speed modem/fax transmission they can support.  I've
always heard the 5510s supported 14400 and anything above that was best
effort.  It would be nice if the new DSPs could transmit at SG3.

Anyone know anything about that ?

On Mon, Feb 8, 2010 at 3:57 PM, Peter Slow <peter.slow at gmail.com> wrote:

> yes, sp2600 DSPs are the PVDM3s. they are completely different from
> the 5510 / PVDM2s and there are limitations as to their coexistence
> within the same chassis. if you want to see what the capabilities of
> your PVDM3 are, you can use the command "show voice dsp capabilities"
> and see some interesting output. I'm not sure about the specific video
> capabilities other than that there will be some. Ive heard video
> specific rumors but since i don't know facts about them i'll keep my
> yap shut ;)
>
> -Peter
>
> On Mon, Feb 8, 2010 at 9:30 AM, Lelio Fulgenzi <lelio at uoguelph.ca> wrote:
> >
> > my 3945 is out of the box, and i needed to do a 'show voice dsp detailed'
> to get SP2600
> >
> > are they these?
> >
> > http://news.thomasnet.com/fullstory/552559
> >
> > ---
> > Lelio Fulgenzi, B.A.
> > Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> > (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> > ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> > Cooking with unix is easy. You just sed it and forget it.
> >                               - LFJ (with apologies to Mr. Popeil)
> >
> >
> > ----- Original Message -----
> > From: "Jason Shearer" <jshearer at amedisys.com>
> > To: "Mark Holloway" <mh at markholloway.com>
> > Cc: "Lelio Fulgenzi" <lelio at uoguelph.ca>, cisco-voip at puck.nether.net
> > Sent: Monday, February 8, 2010 7:30:47 AM GMT -05:00 US/Canada Eastern
> > Subject: RE: [cisco-voip] 3845 DSP
> >
> > Interesting.  I’ll see what info I can squeeze out of my account team.
> Definitely looks like a completely different architecture.  Can someone that
> is running a PVDM3 get us a ‘show voice dsp’ to see what the chipset is?
> >
> >
> >
> > Jason
> >
> >
> >
> > From: Mark Holloway [mailto:mh at markholloway.com]
> > Sent: Sunday, February 07, 2010 10:15 PM
> > To: Jason Shearer
> > Cc: Lelio Fulgenzi; cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] 3845 DSP
> >
> >
> >
> > Unfortunately the product specification for the PVDM2 and PVDM3 are
> listed in two totally different formats.  The PVDM2 product spec is very
> forthcoming in stating the PVDM2 uses Texas Instruments DSP and runs at
> either 200mhz or 175mhz.  The specification for PVDM3 doesn't state what
> type of DSP is used or the clock cycles.  It only says "Multicore DSP
> technology" - so I don't think Cisco wants to share that information right
> now.  It's possible that once someone gets their hands on one they will know
> more information.
> >
> >
> >
> > It's not easy to find details about video and the PVDM3.  Perhaps video
> conference mixing?  The following is the closest thing I could find. "Video
> feature ready"
> >
> >
> >
> >
> >
> > On Feb 7, 2010, at 6:15 AM, Jason Shearer wrote:
> >
> > The PVDM2-64 and PVDM3-64 are the same price ($3200 list) although you
> can get them in much denser versions.  Has anyone run into any problems or
> flakiness with the v3’s?  Are they running the same 5510 chipset?
> >
> >
> >
> > One thing that is interesting is that it says it is a “voice and video”
> DSP.  What does this mean?  Is it going to be able to transcode or mix
> video?
> >
> >
> >
> > Jason
> >
> >
> >
> > From: cisco-voip-bounces at puck.nether.net [mailto:
> cisco-voip-bounces at puck.nether.net] On Behalf Of Mark Holloway
> > Sent: Saturday, February 06, 2010 11:32 AM
> > To: Lelio Fulgenzi
> > Cc: cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] 3845 DSP
> >
> >
> >
> > The new PVDM3 modules are great. They are more expensive than PVDM2 of
> course, but they serve their purpose well.
> >
> >
> >
> > Conferencing, Transcoding, and Transrating Services
> >
> > The PVDM3 modules support digital voice connections, analog voice
> connections, conferencing, and universal transcoding services. The same DSPs
> on the PVDM3 modules can now support all the services with a single DSP
> image. In addition, the PVDM3 supports a higher number of conference
> sessions and a higher number of participants per conference than the PVDM2.
> The PVDM3-256 can support up to 6 conferences with 64 participants in each
> conference and up to 66 conferences with 8 participants in each conference.
> >
> >
> >
> >
> >
> > <image001.png>
> >
> >
> >
> >
> >
> > On Feb 5, 2010, at 5:27 PM, Lelio Fulgenzi wrote:
> >
> >
> > I believe you can configure only one software bridge per server, or in
> retrospect you can configure a server as a software bridge only once.
> >
> > I believe it takes some serious resources to run as a software bridge so
> you don't want to be doing it on your publisher or any subscribers that are
> close to capacity. If you have a standalone DHCP/TFTP server in your design,
> you should be able to get away with using that.
> >
> > A software bridge does not have the hardware limitations w/ number of
> conference participants or number of conferences, but the system will just
> die if it can't keep up.
> >
> > I haven't done a cost analysis, but I still think it would be cheaper to
> buy a small router with lots of DSPs and use that than to install and
> maintain CCM box.
> >
> > ---
> > Lelio Fulgenzi, B.A.
> > Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> > (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> > ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> > Cooking with unix is easy. You just sed it and forget it.
> >                               - LFJ (with apologies to Mr. Popeil)
> >
> >
> > ----- Original Message -----
> > From: "Robert Shearrill" <rshearri at uchicago.edu>
> > To: cisco-voip at puck.nether.net
> > Sent: Friday, February 5, 2010 6:22:21 PM GMT -05:00 US/Canada Eastern
> > Subject: [cisco-voip] 3845 DSP
> >
> > Can some one tell me if i remove all my hardware conf bridges, how many
> software conf bridges will i have and how are they used. I am version 7.1.2
> CCUM.
> >
> >
> >
> > How many software conf bridges do i have per server?
> >
> >
> >
> > Thanks
> >
> >
> >
> > Robert
> >
> > _______________________________________________ cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> >
> >
> >
> >
> > ________________________________
> >
> > *** NOTICE--The attached communication contains privileged and
> confidential information. If you are not the intended recipient, DO NOT
> read, copy, or disseminate this communication. Non-intended recipients are
> hereby placed on notice that any unauthorized disclosure, duplication,
> distribution, or taking of any action in reliance on the contents of these
> materials is expressly prohibited. If you have received this communication
> in error, please delete this information in its entirety and contact the
> Amedisys Privacy Hotline at 1-866-518-6684. Also, please immediately notify
> the sender via e-mail that you have received this communication in error.
> ***
> >
> >
> >
> > ________________________________
> > *** NOTICE--The attached communication contains privileged and
> confidential information. If you are not the intended recipient, DO NOT
> read, copy, or disseminate this communication. Non-intended recipients are
> hereby placed on notice that any unauthorized disclosure, duplication,
> distribution, or taking of any action in reliance on the contents of these
> materials is expressly prohibited. If you have received this communication
> in error, please delete this information in its entirety and contact the
> Amedisys Privacy Hotline at 1-866-518-6684. Also, please immediately notify
> the sender via e-mail that you have received this communication in error.
> ***
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100209/cde56c2f/attachment.html>