[cisco-voip] help with WS-SVC-CMM-6T1

[Scott Voll]

MGCP or H323?

!
controller T1 0/0/0
 clock source line primary
 pri-group timeslots 1-24 <-- I'm guessing maybe the timeslots?

Switch type?



Scott



On Mon, Mar 8, 2010 at 2:53 PM, Frank Arrasmith
<frank.arrasmith at gmail.com>wrote:

> Hi all,
>     I am trying to configure a  6 port T1 module in a CMM, and am
> thoroughly stumped.  I have a T1 drop that was tested good and comes up when
> connected to a 3800 with a T1 VWIC card.   The T1 will not come up to any of
> the ports on the 6T1 module on the CMM.  The Controller configs are
> identical on the router and the CMM.  I get a green LED on the CMM card but
> thats it.  The weird part is that the router T1 will come up to the carrier
> T1, a T1 loopback, and even the T1 connected to the CMM module with a
> crossover T1 cable.   The CMM module will not come up to a loopback, nor the
> Router t1, nor the carrier t1(but the LED will green up).  I could not find
> any documentation on a different Pinout for CMM module, so my guess is I am
> missing something in the config.  Is there anything special needed for these
> CMM modules, or anybody have a suggestion on a command to troubleshoot the
> Layer 1 issue?
>
> *Config for CMM:*
> #show controllers t1 1/0 brief
> T1 1/0 is down.
>   Applique type is Channelized T1
>   Cablelength is long gain36 0db
>   Receiver has loss of signal.
>   alarm-trigger is not set
>   Soaking time: 3, Clearance time: 10
>   AIS State:Clear  LOS State:Clear  LOF State:Clear
>   Framing is ESF, Line Code is B8ZS, Clock Source is Line.
>
> #show int se1/0:23
> Serial1/0:23 is reset, line protocol is down
>   Hardware is DSX1
>   MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
>      reliability 255/255, txload 1/255, rxload 1/255
>   Encapsulation HDLC, loopback not set
>
> #show isdn status
> Global ISDN Switchtype = primary-ni
> ISDN Serial1/0:23 interface
>         dsl 0, interface ISDN Switchtype = primary-ni
>     Layer 1 Status:
>         DEACTIVATED
>     Layer 2 Status:
>         TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
>     Layer 3 Status:
>         0 Active Layer 3 Call(s)
>     Active dsl 0 CCBs = 0
>     The Free Channel Mask:  0x00000000
>     Number of L2 Discards = 0, L2 Session ID = 0
>
> *
> Config for the T1 VWIC:*
> #show controllers t1 0/1/0 brief
> T1 0/1/0 is up.
>   Applique type is Channelized T1
>   Cablelength is long gain36 0db
>   No alarms detected.
>   alarm-trigger is not set
>   Soaking time: 3, Clearance time: 10
>   AIS State:Clear  LOS State:Clear  LOF State:Clear
>   Version info Firmware: 20040802, FPGA: 13, spm_count = 0
>   Framing is ESF, Line Code is B8ZS, Clock Source is Line.
>
> Serial0/1/0:23 is up, line protocol is up (spoofing)
>   Hardware is DSX1
>   MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
>      reliability 255/255, txload 1/255, rxload 1/255
>   Encapsulation HDLC, loopback not set
>
> ISDN Serial0/1/0:23 interface
>         dsl 0, interface ISDN Switchtype = primary-ni
>         L2 Protocol = Q.921 0x0000  L3 Protocol(s) = CCM MANAGER 0x0003
>     Layer 1 Status:
>         ACTIVE
>     Layer 2 Status:
>         TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
>     Layer 3 Status:
>         0 Active Layer 3 Call(s)
>     Active dsl 0 CCBs = 0
>     The Free Channel Mask:  0x807FFFFF
>     Number of L2 Discards = 0, L2 Session ID = 23
>
>
>
>
>
>
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100308/df8d33b2/attachment.html>