[cisco-voip] WAS MWI ISSUE-- now--CDR/SNR question

[Wes Sisk]

Jim,

I have not explicitly tested but with "log zero duration calls" enabled 
I would expect to see the call leg "sent to a Cell phone passing thru 
CCM" appear in CDR.  Depending on your profile settings (answer too 
soon, answer too late) the call may get connected to cell phone 
voicemail which would send it to fully connected state and give it a 
non-zero duration.

/Wes

On Thursday, May 13, 2010 3:12:10 PM, Jim McBurnett 
<jim at tgasolutions.com> wrote:
>
> Wes,
>
> This makes me ask a question---
>
> If mobility and SNR is enabled--- Will a call sent to a Cell phone 
> passing thru CCM appear as a zero duration call in CDR?---
>
> IE It goes to my cell phone and I don't answer it and it goes back to 
> Unity... Will that appear? If not, why not?
>
>  
>
> Thanks,
>
> Jim
>
>  
>
> *From:* cisco-voip-bounces at puck.nether.net 
> [mailto:cisco-voip-bounces at puck.nether.net] *On Behalf Of *Wes Sisk
> *Sent:* Thursday, May 13, 2010 3:06 PM
> *To:* Mike J. Erickson
> *Cc:* cisco-voip at puck.nether.net
> *Subject:* Re: [cisco-voip] MWI Issue
>
>  
>
> I would start by enabling 0 duration call detail records (cm service 
> parameter).  Then see what time his MWI gets set (call from his 
> extension number to the MWI ON number).  If you find the CDR is the 
> originating device a phone or is it a voicemail port?  If a voicemail 
> port and call falls within the time when unity is doing MWI refresh 
> then need to investigate Unity.  If originating device is not Unity 
> then need to investigate the originating device.  Could be as simple 
> as coworker playing prank.  Do you allow phones to dial the mwi on/off 
> numbers directly?
>
> If it does not appear in CDR then get CM SDI and SDL traces from the 
> overnight period.  TAC can find when the MWI was set and what 
> initiated the MWI operation.
>
> If you have Q.SIG trunks keep in mind MWI operations can pass over 
> Q.SIG as well.
>
> /Wes
>
> On Thursday, May 13, 2010 1:58:53 PM, Mike J. Erickson 
> <mjerickson at orbits.net> <mailto:mjerickson at orbits.net> wrote:
>
> Running CUCM 7.12 and Unity 7.0.  I have one user out of 600 that gets 
> his MWI light turned on every morning after the MWI refresh cycle, 
> despite the fact there aren't any VM's in his inbox.  Here are the 
> steps that have been done:
>
>  
>
> 1) Deleted his Unity Profile and Recreated it
>
> 2) Deleted his Phone Profile and Recreated it
>
> 3) Tried logging in as him on a different phone
>
> 4) Failed over and rebooted Primary. Failed back to Primary and it is 
> still happening
>
> 5) Logged into his Exchange mailbox (Not cached) and there were no 
> unread messages nor any VMs in his inbox or any other folders. There 
> were no rules set in Outlook as well
>
> 6) Logged into his VM Box on the phone and there were no new 
> Voicemails or Messages
>
>  
>
> Not sure where else to look.  Thanks in advance.
>
>  
>
>  
>
>  
> ------------------------------------------------------------------------
>
>
>   
>  
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net <mailto:cisco-voip at puck.nether.net>
> https://puck.nether.net/mailman/listinfo/cisco-voip
>   
>
>  
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100521/ebca47e1/attachment.html>