[cisco-voip] cannot direct call to Unity with TCL script

[Dew Swen]

Thanks Craig,

I will do the config and tell the result.

Regards,

-- 
Dew Swen
CCVP, CCNP



28.05.2010 14:33, Craig Staffin yazmış:
> Yes but TCL does not
>
> So your incoming call leg is g711 the outgoing needs to be the same. 
> Or invoke a transcoder useing CUBE   Lots more config...
>
> Craig Staffin
> Lead voice consulting engineer - CCNA, CCVP, CCIE# 25802 (Voice)
> Core BTS
> +1 262 754 2634
> craig.staffin at corebts.com <mailto:craig.staffin at corebts.com>
>
> On May 28, 2010, at 6:29 AM, Dew Swen <dew.swen at gmail.com 
> <mailto:dew.swen at gmail.com>> wrote:
>
>> Hi Craig,
>>
>> But Unity talks g729 ?
>> -- 
>> Dew Swen
>> CCVP, CCNP
>>
>>
>> 28.05.2010 14:11, Craig Staffin yazmış:
>>>
>>> Voip dialpeers are g729 by default
>>>
>>> Add codec g711 under the unity one.
>>>
>>> Craig Staffin
>>> Lead voice consulting engineer - CCNA, CCVP, CCIE# 25802 (Voice)
>>> Core BTS
>>> +1 262 754 2634
>>> craig.staffin at corebts.com <mailto:craig.staffin at corebts.com>
>>>
>>> On May 28, 2010, at 5:47 AM, Dew Swen <dew.swen at gmail.com 
>>> <mailto:dew.swen at gmail.com>> wrote:
>>>
>>>> The flow is something like that:
>>>>
>>>> I forwarded the call after 15 secs to a route pattern (666669999) 
>>>> from extention's line settings. Route pattern directs call to gateway.
>>>>
>>>> I created this dial-peer in order to trigger the tcl script:
>>>>
>>>> dial-peer voice 1111 voip
>>>>  service unity
>>>>  codec g711ulaw
>>>>  incoming called-number 666669999
>>>>
>>>> After that,  in order to sent call to Unity's pilot number (5000) I 
>>>> created this dial-peer:
>>>>
>>>> dial-peer voice 1112 voip
>>>>  destination-pattern 5000
>>>>  session target ipv4:10.10.10.11
>>>>
>>>> 10.10.10.11 is the CUCM's IP address.
>>>>
>>>>
>>>> Do I need a xcoder?
>>>>
>>>> Because when I directs call to another extention or PSTN number, it 
>>>> works fine.
>>>>
>>>> -
>>>> Dew Swen
>>>> CCVP, CCNP
>>>>
>>>>
>>>> 2010/5/28 Dew Swen <dew.swen at gmail.com <mailto:dew.swen at gmail.com>>
>>>>
>>>>     Hi there,
>>>>
>>>>     I want to direct call to Unity with a TCL script on a Cisco
>>>>     router. Script works fine when I direct call to another
>>>>     extention or PSTN number. But when I forward the call to
>>>>     Unity's pilot number, the call stays in suspense and hangs up.
>>>>
>>>>     The script is attached. First it plays a message then directs
>>>>     it to Unity.
>>>>
>>>>     Is there anything related codec issue? Any thoughts will be
>>>>     helpful.
>>>>
>>>>     Regards,
>>>>
>>>>     -- 
>>>>     Dew Swen
>>>>     CCVP, CCNP
>>>>
>>>>
>>>> _______________________________________________
>>>> cisco-voip mailing list
>>>> cisco-voip at puck.nether.net <mailto:cisco-voip at puck.nether.net>
>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100528/a9cc02d6/attachment.html>