[cisco-voip] dial-peer E1 ISDN

[Just Kennie]

Paul/ccieidot1,

well I have a fsx voice-port of (but not in use)

*voice-port 0/0/0
!
voice-port 0/0/1
!
voice-port 0/0/2*
!
*voice-port 0/0/3*
!
and an E1 interface of... (connected to remote router)

*controller E1 0/2/0
 framing NO-CRC4
 channel-group 0 timeslots 1-31
 !
 interface Serial0/2/0:0
 description G703.E1.Connection to Customer router
 bandwidth 2048
 no ip address
encap HDLC*
!
I am using the E1 interface to connect to a remote router with E1 interface
too at the other end with above config

May challenge is, I want to configure a dial-peer that will route all my
voice traffic destined to 1000 through the E1 card, so i configure the
following....

*dial-peer voice 1 pots
destination-pattern 21232
session target port 0/0/0:0
!
*but saw the following error....*

MY_ROUTER(config-dial-peer)#session target port 0/2/0:0

   ^
% Invalid input detected at '^' marker.

*Also when I use *port 0/2/0:0* as advised by ccieidot1, I receive the
following message..*

MY_ROUTER(config-dial-peer)#port 0/2/0:0
                                                             ^
% Invalid input detected at '^' marker.
!
*
Please assist, as what I want to achieve is to route all voice traffic
destined to 1000 at the remote site through the E1 interface.






*Cheers,
Idowu Kehinde
TEL: 2348024017748
BB:  30E8E5F9
*



On Mon, Feb 7, 2011 at 7:09 PM, Paul <asobihoudai at yahoo.com> wrote:

> What is the label on your voice-port?
>
> I'm going to guess that your voice-port is also 0/2/0:0...I've never
> touched an E1 so I am a little bit confused when I don't see :31 at the end
> instead of the "0" you have there but..it looks like you're trying to send
> calls to a voice port that doesn't exist and you're trying to use session
> target when that's used for voip dial peers.
>
> You're looking for
> port 0/2/0:0 instead.
>
> ------------------------------
> *From:* Just Kennie <justkennie at gmail.com>
> *To:* cisco-voip at puck.nether.net
> *Sent:* Mon, February 7, 2011 10:00:42 AM
> *Subject:* [cisco-voip] dial-peer E1 ISDN
>
> Hi All,
> I am trying to configure my E1 card for ISDN connectivity for voice
> traffic, below is my config...
>
> *controller E1 0/2/0
>  framing NO-CRC4
>  channel-group 0 timeslots 1-31
> !
> interface Serial0/2/0:0
>  description G703.E1.Connection to Customer
>  bandwidth 2048
>  no ip address*
> *encapp HDLC*
> *!*
> Now I am trying to configure the Dial-peer, to forward 2123 calls through
> the E1 ISDN interface
> !
> *dial-peer voice 1 pots
> destination-pattern 21232
> session target port 0/0/0:0*
> !
> but its my 2811 voice gateway is not allowing the "session target port
> 0/0/0:0" command, please what should I do to forward my calls through the E1
> ISDN interface.
>
>
>
> *Cheers,
> Idowu Kehinde
> TEL: 2348024017748
> BB:  30E8E5F9
> *
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20110207/04207292/attachment.html>