[cisco-voip] dial-peer E1 ISDN

[Paul]

I'm not understanding your setup. If this is supposed to be ISDN PRI, where is 
your PRI group? I've never heard or performed a G.703 ISDN setup..<?>



________________________________
From:Just Kennie <justkennie at gmail.com>
To:Joel Perez <tman701 at gmail.com>
Cc:Paul <asobihoudai at yahoo.com>; ccieid1ot at gmail.com; cisco-voip at puck.nether.net
Sent: Mon, February 7, 2011 1:00:44 PM
Subject: Re: [cisco-voip] dial-peer E1 ISDN

Cciedot1ot, I am using the E1 for voice, and its like an ISDN setup, that's why 
there is no ipv4 address. its G.703.
Joel, I did what you said I should do...

controller E1 0/2/0
 framing NO-CRC4 
 channel-group 15 timeslots 1-31
 description G703.E1.Connection to customer
!
interface Serial0/2/0:15
 description G703.E1.Connection to customer
 bandwidth 2048
 no ip address
!
And see the below error when i want to map port to it.

dial-peer voice 1 pots
 destination-pattern 1000
MY_ROUTER(config-dial-peer)#port 0/2/0:15
                                                          ^
% Invalid input detected at '^' marker.

In my own opinion, I guess "port 0/2/0:15" is trying used when specifying an 
FSX/FSO port, but here, I want to specify the E1 interface for the voice traffic 
destined for 1000 on a remote router.

REALLY NEED HELP !!!



Cheers,
Idowu Kehinde
TEL: 2348024017748
BB:  30E8E5F9

 



On Mon, Feb 7, 2011 at 8:04 PM, Joel Perez <tman701 at gmail.com> wrote:

If im understanding correctly what you are trying to do then you have a few 
things wrong.
>
>
>for E1's I use channel 15 for the D-channel:
> interface Serial0/2/0:15 
>
>
>For the dial peers like it was pointed out it needs to be a POTS dial peer and 
>also needs to point to D channel 15.
>port 0/2/0:15
>
>
>"session target" is used to send to an IPv4 address.
>
>
>Hope that helps,
>
>
>Joel P
>
>
>On Mon, Feb 7, 2011 at 1:40 PM, Just Kennie <justkennie at gmail.com> wrote:
>
>Paul/ccieidot1,
>>
>>well I have a fsx voice-port of (but not in use)
>>
>>voice-port 0/0/0
>>!         
>>voice-port 0/0/1
>>!         
>>voice-port 0/0/2
>>!         
>>voice-port 0/0/3
>>!
>>and an E1 interface of... (connected to remote router)
>>
>>controller E1 0/2/0
>> framing NO-CRC4 
>> channel-group 0 timeslots 1-31
>> !
>> interface Serial0/2/0:0
>> description G703.E1.Connection to Customer router
>>
>> bandwidth 2048
>> no ip address
>>encap HDLC
>>!
>>I am using the E1 interface to connect to a remote router with E1 interface too 
>>at the other end with above config
>>
>>May challenge is, I want to configure a dial-peer that will route all my voice 
>>traffic destined to 1000 through the E1 card, so i configure the following....
>>
>>
>>dial-peer voice 1 pots
>>destination-pattern 21232
>>session target port 0/0/0:0
>>!
>>but saw the following error....
>>
>>MY_ROUTER(config-dial-peer)#session target port 0/2/0:0              
>>                                                                              
^
>>% Invalid input detected at '^' marker.
>>
>>Also when I use port 0/2/0:0 as advised by ccieidot1, I receive the following 
>>message..
>>
>>MY_ROUTER(config-dial-peer)#port 0/2/0:0              
>>                                                             ^
>>% Invalid input detected at '^' marker.
>>!
>>
>>Please assist, as what I want to achieve is to route all voice traffic destined 
>>to 1000 at the remote site through the E1 interface.
>>
>>
>> 
>>
>>
>>
>>
>>Cheers,
>>Idowu Kehinde
>>TEL: 2348024017748
>>BB:  30E8E5F9
>>
>> 
>>
>>
>>
>>On Mon, Feb 7, 2011 at 7:09 PM, Paul <asobihoudai at yahoo.com> wrote:
>>
>>What is the label on your voice-port?
>>>
>>>
>>>I'm going to guess that your voice-port is also 0/2/0:0...I've never touched an 
>>>E1 so I am a little bit confused when I don't see :31 at the end instead of the 
>>>"0" you have there but..it looks like you're trying to send calls to a voice 
>>>port that doesn't exist and you're trying to use session target when that's used 
>>>for voip dial peers.
>>>
>>>
>>>You're looking for
>>>port 0/2/0:0 instead.
>>>
>>>
>>>
________________________________
From:Just Kennie <justkennie at gmail.com>
>>>To:cisco-voip at puck.nether.net
>>>Sent: Mon, February 7, 2011 10:00:42 AM
>>>Subject: [cisco-voip] dial-peer E1 ISDN
>>>
>>>
>>>Hi All,
>>>I am trying to configure my E1 card for ISDN connectivity for voice traffic, 
>>>below is my config...
>>>
>>>controller E1 0/2/0
>>> framing NO-CRC4 
>>> channel-group 0 timeslots 1-31
>>>!
>>>interface Serial0/2/0:0
>>> description G703.E1.Connection to Customer
>>> bandwidth 2048
>>> no ip address
>>>encapp HDLC
>>>!
>>>Now I am trying to configure the Dial-peer, to forward 2123 calls through the E1 
>>>ISDN interface
>>>!
>>>dial-peer voice 1 pots
>>>destination-pattern 21232
>>>session target port 0/0/0:0
>>>! 
>>>but its my 2811 voice gateway is not allowing the "session target port 0/0/0:0" 
>>>command, please what should I do to forward my calls through the E1 ISDN 
>>>interface.
>>>
>>>
>>>
>>>Cheers,
>>>Idowu Kehinde
>>>TEL: 2348024017748
>>>BB:  30E8E5F9
>>>
>>> 
>>>
>>>
>>
>>_______________________________________________
>>cisco-voip mailing list
>>
>>cisco-voip at puck.nether.net
>>https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>



      
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20110207/bb6225d2/attachment.html>