[cisco-voip] dial-peer E1 ISDN
Joel Perez
tman701 at gmail.com
Mon Feb 7 21:07:17 EST 2011
Ok i was under the impression that the E1 was a PRI for Voice.
If the E1 is just a data uplink to another GW somewhere else then you need a
voip dial peer and a "destination address" in that voip dial peer. The
"destination address" should be the IP of the receiving GW, not your own E1
interface.
Can you sort of describe your intended call flow? If
On Mon, Feb 7, 2011 at 5:59 PM, Just Kennie <justkennie at gmail.com> wrote:
> Sorry not ISDN, HDLC encapsulation on the s0/2/0:15 I mean. I guess I just
> explained the setup. Trying to route traffic through an E1 interface to a
> remote destination that all !
> I have written my present config out,and that all. Just need someone to
> help me with this, since the interface doesnt use an IP address.
>
>
> *Cheers,
> Idowu Kehinde
> TEL: 2348024017748
> BB: 30E8E5F9
> *
>
>
>
> On Mon, Feb 7, 2011 at 11:18 PM, Paul <asobihoudai at yahoo.com> wrote:
>
>> I'm not understanding your setup. If this is supposed to be ISDN PRI,
>> where is your PRI group? I've never heard or performed a G.703 ISDN
>> setup..<?>
>>
>> ------------------------------
>> *From:* Just Kennie <justkennie at gmail.com>
>> *To:* Joel Perez <tman701 at gmail.com>
>> *Cc:* Paul <asobihoudai at yahoo.com>; ccieid1ot at gmail.com;
>> cisco-voip at puck.nether.net
>> *Sent:* Mon, February 7, 2011 1:00:44 PM
>> *Subject:* Re: [cisco-voip] dial-peer E1 ISDN
>>
>> Cciedot1ot, I am using the E1 for voice, and its like an ISDN setup,
>> that's why there is no ipv4 address. its G.703.
>> Joel, I did what you said I should do...
>>
>> *controller E1 0/2/0
>> framing NO-CRC4
>> channel-group 15 timeslots 1-31
>> description G703.E1.Connection to customer
>> !
>> interface Serial0/2/0:15
>> description G703.E1.Connection to customer
>> bandwidth 2048
>> no ip address
>> !*
>> And see the below error when i want to map port to it.
>>
>> *dial-peer voice 1 pots
>> destination-pattern 1000
>> **MY_ROUTER(config-dial-peer)#port 0/2/0:15
>> ^
>> % Invalid input detected at '^' marker.
>> *
>> In my own opinion, I guess "*port 0/2/0:15*" is trying used when
>> specifying an FSX/FSO port, but here, I want to specify the E1 interface for
>> the voice traffic destined for 1000 on a remote router.
>>
>> *REALLY NEED HELP !!!*
>>
>>
>>
>> *Cheers,
>> Idowu Kehinde
>> TEL: 2348024017748
>> BB: 30E8E5F9
>> *
>>
>>
>>
>> On Mon, Feb 7, 2011 at 8:04 PM, Joel Perez <tman701 at gmail.com> wrote:
>>
>>> If im understanding correctly what you are trying to do then you have a
>>> few things wrong.
>>>
>>> for E1's I use channel 15 for the D-channel:
>>> * *interface Serial0/2/0:15
>>>
>>> For the dial peers like it was pointed out it needs to be a POTS dial
>>> peer and also needs to point to D channel 15.
>>> port 0/2/0:15
>>>
>>> "session target" is used to send to an IPv4 address.
>>>
>>> Hope that helps,
>>>
>>> Joel P
>>>
>>> On Mon, Feb 7, 2011 at 1:40 PM, Just Kennie <justkennie at gmail.com>wrote:
>>>
>>>> Paul/ccieidot1,
>>>>
>>>> well I have a fsx voice-port of (but not in use)
>>>>
>>>> *voice-port 0/0/0
>>>> !
>>>> voice-port 0/0/1
>>>> !
>>>> voice-port 0/0/2*
>>>> !
>>>> *voice-port 0/0/3*
>>>> !
>>>> and an E1 interface of... (connected to remote router)
>>>>
>>>> *
>>>> controller E1 0/2/0
>>>> framing NO-CRC4
>>>> channel-group 0 timeslots 1-31
>>>> !
>>>> interface Serial0/2/0:0
>>>> description G703.E1.Connection to Customer router
>>>>
>>>> bandwidth 2048
>>>> no ip address
>>>> encap HDLC*
>>>> !
>>>> I am using the E1 interface to connect to a remote router with E1
>>>> interface too at the other end with above config
>>>>
>>>> May challenge is, I want to configure a dial-peer that will route all my
>>>> voice traffic destined to 1000 through the E1 card, so i configure the
>>>> following....
>>>>
>>>>
>>>> *dial-peer voice 1 pots
>>>> destination-pattern 21232
>>>> session target port 0/0/0:0
>>>> !
>>>> *
>>>> but saw the following error....*
>>>>
>>>> MY_ROUTER(config-dial-peer)#session target port 0/2/0:0
>>>>
>>>> ^
>>>> % Invalid input detected at '^' marker.
>>>>
>>>> *Also when I use *port 0/2/0:0* as advised by ccieidot1, I receive the
>>>> following message..*
>>>>
>>>> MY_ROUTER(config-dial-peer)#port 0/2/0:0
>>>> ^
>>>> % Invalid input detected at '^' marker.
>>>> !
>>>> *
>>>> Please assist, as what I want to achieve is to route all voice traffic
>>>> destined to 1000 at the remote site through the E1 interface.
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> *Cheers,
>>>> Idowu Kehinde
>>>> TEL: 2348024017748
>>>> BB: 30E8E5F9
>>>> *
>>>>
>>>>
>>>>
>>>> On Mon, Feb 7, 2011 at 7:09 PM, Paul <asobihoudai at yahoo.com> wrote:
>>>>
>>>>> What is the label on your voice-port?
>>>>>
>>>>> I'm going to guess that your voice-port is also 0/2/0:0...I've never
>>>>> touched an E1 so I am a little bit confused when I don't see :31 at the end
>>>>> instead of the "0" you have there but..it looks like you're trying to send
>>>>> calls to a voice port that doesn't exist and you're trying to use session
>>>>> target when that's used for voip dial peers.
>>>>>
>>>>> You're looking for
>>>>> port 0/2/0:0 instead.
>>>>>
>>>>> ------------------------------
>>>>> *From:* Just Kennie <justkennie at gmail.com>
>>>>> *To:* cisco-voip at puck.nether.net
>>>>> *Sent:* Mon, February 7, 2011 10:00:42 AM
>>>>> *Subject:* [cisco-voip] dial-peer E1 ISDN
>>>>>
>>>>> Hi All,
>>>>> I am trying to configure my E1 card for ISDN connectivity for voice
>>>>> traffic, below is my config...
>>>>>
>>>>> *controller E1 0/2/0
>>>>> framing NO-CRC4
>>>>> channel-group 0 timeslots 1-31
>>>>> !
>>>>> interface Serial0/2/0:0
>>>>> description G703.E1.Connection to Customer
>>>>> bandwidth 2048
>>>>> no ip address*
>>>>> *encapp HDLC*
>>>>> *!*
>>>>> Now I am trying to configure the Dial-peer, to forward 2123 calls
>>>>> through the E1 ISDN interface
>>>>> !
>>>>> *dial-peer voice 1 pots
>>>>> destination-pattern 21232
>>>>> session target port 0/0/0:0*
>>>>> !
>>>>> but its my 2811 voice gateway is not allowing the "session target port
>>>>> 0/0/0:0" command, please what should I do to forward my calls through the E1
>>>>> ISDN interface.
>>>>>
>>>>>
>>>>>
>>>>> *Cheers,
>>>>> Idowu Kehinde
>>>>> TEL: 2348024017748
>>>>> BB: 30E8E5F9
>>>>> *
>>>>>
>>>>>
>>>>>
>>>>
>>>> _______________________________________________
>>>> cisco-voip mailing list
>>>>
>>>> cisco-voip at puck.nether.net
>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>>
>>>>
>>>
>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20110207/a0012710/attachment.html>
More information about the cisco-voip
mailing list