[cisco-voip] Caller ID FXO Port

[Wes Sisk]

I believe 'debug vpm signal' will show if CLID is received from the carrier:

<snip>
[2/0/12] htsp_stop_caller_id_rx. message length 26htsp_setup_ind
[2/0/12] get_fxo_caller_id:Caller ID received. Message type=128 
length=26 checksum=92
[2/0/12] Caller ID String <concealed>
</snip>



On 2/11/2011 3:55 PM, David Zhars wrote:
> I believe this has changed with CUCM 8.0.
> Under new features for 8.0 is this:
>
> • MGCP signaling and control to selected Cisco VoIP gateways
>
> – Caller ID for PRI and FXO
>
>
> So it sure seems like it should work.  I have enabled Caller ID in 
> UCM, I have added caller-id enable on the 2801 under the voice-port 
> config.  Still no CID showing up.  Might be time to call in the phone co.
>
>
> I was hoping there was some sort of command I could issue on the 2801 
> when I called, that would show me the caller ID of my cell (if it was 
> being delivered by the phone co).  2801 is running IOS 15.0(1)M4
>
>
> On Fri, Feb 11, 2011 at 3:08 PM, Saboor Khan <saboor.khan at gmail.com 
> <mailto:saboor.khan at gmail.com>> wrote:
>
>     It should be enable under Voice Port for FXO, command as
>
>     caller-id enable
>
>     Also checked with your Telco is that they enable on their end as
>     well as.
>
>
>     Also something if you are using MGCp for FXO, Caller deos not
>     works, it only works with H323, you need to change it to H323 Gateway.
>
>     *Symptoms:*
>
>     You can potentially encounter this list of symptoms when you
>     configure Cisco CallManager with Cisco IOS MGCP gateways with
>     analog FXO and FXS ports:
>
>        *
>
>           The MGCP gateway does not register with Cisco CallManager.
>           Refer to MGCP Gateway Registration Failure with Cisco
>           CallManager
>           <http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00805a316c.shtml>.
>
>        *
>
>           Caller ID does not work on FXO ports. This is because caller
>           ID is not supported with FXO ports when configured for MGCP.
>           Configure the gateway in H.323 mode instead.
>
>        *
>
>           Overhead paging locks up FXO ports during hookflash unless
>           users go completely off-hook. Shut followed by No shut
>           resets the port. This is related to Cisco bug ID CSCef62275
>           <http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCef62275>
>           (registered
>           <http://tools.cisco.com/RPF/register/register.do> customers
>           only) when fixed in Cisco IOS Software Release 12.3(14)T and
>           later.
>
>
>
>     regards
>
>     -Saboor
>
>     On Fri, Feb 11, 2011 at 1:32 PM, Paul <asobihoudai at yahoo.com
>     <mailto:asobihoudai at yahoo.com>> wrote:
>
>         I think you may still have to configure the voice port
>         'callerid enable'. I
>         remember a few years ago when I configured this on the port
>         for CCME, the
>         customer wasn't paying for callerID and this caused callers to
>         hear ringback
>         twice before the phone actually rang on the customer's side.
>
>         I don't know if you're required to configure callerID on the
>         FXO port but I'd
>         think that unless MGCP automagically put that command on the
>         port, I doubt your
>         callerID is going to work.
>
>         ________________________________
>         From:David Zhars <dzhars at gmail.com <mailto:dzhars at gmail.com>>
>         To:Paul <asobihoudai at yahoo.com
>         <mailto:asobihoudai at yahoo.com>>; cisco-voip at puck.nether.net
>         <mailto:cisco-voip at puck.nether.net>
>         Sent: Fri, February 11, 2011 10:22:42 AM
>         Subject: Re: [cisco-voip] Caller ID FXO Port
>
>         Hmmm..no I have not!  I did not know if I had to do this with
>         the router being
>         in MGCP mode.
>         Are the commands the same as for a H323 setup?
>
>
>         On Fri, Feb 11, 2011 at 1:17 PM, Paul <asobihoudai at yahoo.com
>         <mailto:asobihoudai at yahoo.com>> wrote:
>
>         Have you configured the FXO port on the router for caller ID?
>         >
>         >
>         >
>         >________________________________
>         >From:David Zhars <dzhars at gmail.com <mailto:dzhars at gmail.com>>
>         >To:cisco-voip at puck.nether.net
>         <mailto:To%3Acisco-voip at puck.nether.net>
>         >Sent: Fri, February 11, 2011 9:47:04 AM
>         >Subject: [cisco-voip] Caller ID FXO Port
>         >
>         >
>         >Call Manager 8.0.  MGCP 2801 Router.  Line comes in to first
>         FXO port, we have
>         >Caller ID on the line.
>         >
>         >In CM, I have "Enable Caller ID" set under device information.
>         >
>         >Yet all calls come in without caller ID (just "External Call
>         - Unknown Number"
>         >shows up on the phones).
>         >
>         >Is there a way to see if the 2801 gets the Caller ID?  Or any
>         other
>         >troubleshooting I can do?
>         >
>         >Thanks.
>         >
>         >
>         >
>         >
>         >
>
>
>
>
>         _______________________________________________
>         cisco-voip mailing list
>
>         cisco-voip at puck.nether.net <mailto:cisco-voip at puck.nether.net>
>         https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20110211/e61e4362/attachment.html>