[cisco-voip] Now, 7206

[Scott Voll]

What feature set are you running?  IP BASE?  I thought you needed at least
IP plus?  Maybe i'm wrong.

Scott

On Fri, Sep 2, 2011 at 12:35 PM, Joseph Mays <mays at win.net> wrote:

> **
> Well, this sort of thing keeps happening. Now, I'm working on a Cisco 7206
> running c7200-is-mz.123-22.bin. The feature navigator is quite clear that
> qos and autoqos-voip are supported on this router.
>
> Go to global config, enter "mls qos" to enable qos -- invalid input at
> global config.
>
> ==========
> gw1.armplc#show ver
> Cisco Internetwork Operating System Software
> IOS (tm) 7200 Software (C7200-IS-M), Version 12.3(22), RELEASE SOFTWARE
> (fc2)
> Technical Support: http://www.cisco.com/techsupport
> Copyright (c) 1986-2007 by cisco Systems, Inc.
> Compiled Wed 24-Jan-07 20:17 by ccai
> Image text-base: 0x60008AF4, data-base: 0x61D44000
>
> ROM: System Bootstrap, Version 12.1(20000710:044039) [nlaw-121E_npeb 117],
> DEVELOPMENT SOFTWARE
> BOOTLDR: 7200 Software (C7200-IS-M), Version 12.3(22), RELEASE SOFTWARE
> (fc2)
>
> gw1.armplc uptime is 3 weeks, 2 days, 13 hours, 42 minutes
> System returned to ROM by power-on
> System image file is "slot0:c7200-is-mz.123-22.bin"
>
> cisco 7206VXR (NPE400) processor (revision A) with 491520K/32768K bytes of
> memory.
> Processor board ID 29496245
> R7000 CPU at 350MHz, Implementation 39, Rev 3.2, 256KB L2 Cache
> 6 slot VXR midplane, Version 2.7
>
> Last reset from power-on
> Bridging software.
> X.25 software, Version 3.0.0.
> Primary Rate ISDN software, Version 1.1.
>
> PCI bus mb0_mb1 (Slots 0, 1, 3 and 5) has a capacity of 600 bandwidth
> points.
> Current configuration on bus mb0_mb1 has a total of 470 bandwidth points.
> This configuration is within the PCI bus capacity and is supported.
>
> PCI bus mb2 (Slots 2, 4, 6) has a capacity of 600 bandwidth points.
> Current configuration on bus mb2 has a total of 380 bandwidth points
> This configuration is within the PCI bus capacity and is supported.
>
> Please refer to the following document "Cisco 7200 Series Port Adaptor
> Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>
> for c7200 bandwidth points oversubscription and usage guidelines.
>
>
> 2 FastEthernet/IEEE 802.3 interface(s)
> 31 Serial network interface(s)
> 1 ATM network interface(s)
> 1 Channelized T3 port(s)
> 125K bytes of non-volatile configuration memory.
>
> 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
> 4096K bytes of Flash internal SIMM (Sector size 256K).
> Configuration register is 0x2102
>
> gw1.armplc#config
> Configuring from terminal, memory, or network [terminal]? t
> Enter configuration commands, one per line.  End with CNTL/Z.
> gw1.armplc(config)#mls qos
>                        ^
> % Invalid input detected at '^' marker.
>
> gw1.armplc(config)#exit
> gw1.armplc#
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20110902/777eff7d/attachment.html>