[cisco-voip] Calls to DS-'s across channelized T1, no calling number at CPE

[Nick Matthews]

Couple things, not sure of any of these will solve the problem:
-Remove 'direct-inward-dial' on the FXS port. Only for PRI's.
-Need to enable caller ID on FXS. 'caller-id enable' on voice-port 2/0
-May also need caller-id on voice-port 1/0:24 also.

-nick

On Fri, Jul 6, 2012 at 11:43 PM, Jonathan Charles <jonvoip at gmail.com> wrote:

> I am lazy, I would just back to back PRI it...
>
>
>
>
> Jonathan
>
>
> On Fri, Jul 6, 2012 at 10:01 PM, Southeasttexas Telecom <
> SETXTelecom at att.net> wrote:
>
>> He’ll need to change the type on the IAD to FXS as well but isn’t there a
>> tie or similar setting that would better match what he is doing (and used
>> on both ends)?…….Using Ground start ? I would set it to Wink Start if
>> available.****
>>
>> ** **
>>
>> *From:* cisco-voip-bounces at puck.nether.net [mailto:
>> cisco-voip-bounces at puck.nether.net] *On Behalf Of *Jonathan Charles
>> *Sent:* Friday, July 06, 2012 8:21 PM
>> *To:* Joseph Mays
>> *Cc:* cisco-voip at puck.nether.net
>> *Subject:* Re: [cisco-voip] Calls to DS-'s across channelized T1, no
>> calling number at CPE****
>>
>> ** **
>>
>> They are set to FXS, they won't send digits... (it is acting like a
>> station port...)****
>>
>> ** **
>>
>> You will need to set them to FGD or FXO...****
>>
>> ** **
>>
>> ds0-group 0 timeslots 1-2 type fgd-eana****
>>
>> ** **
>>
>> ** **
>>
>> ** **
>>
>> Jonathan****
>>
>> ** **
>>
>> On Fri, Jul 6, 2012 at 1:18 PM, Joseph Mays <mays at win.net> wrote:****
>>
>> I'm configuring an AS5400 to provide a channelized t1 to an IAD2400. 4 of
>> the channels on the T1 are being used for a DS0 group across which we want
>> the AS5400 to handle voice calls to and from the IAD2400.****
>>
>>  ****
>>
>> On the AS5400****
>>
>>  ****
>>
>> controller T1 1/0:24
>>  framing esf
>>  channel-group 0 timeslots 1-20 speed 64
>>  loopback network ignore
>>  ds0-group 20 timeslots 21-24 type fxs-ground-start
>> !
>> interface Serial1/0:24:0
>>  ip address 216.24.2.5 255.255.255.252
>>  no cdp enable
>> !
>> voice-port 1/0:24:20
>> !
>> dial-peer voice 248 pots
>>  description ATA-8 TEST line 2, WinNETPBX
>>  incoming called-number 502567301[1-9]
>>  destination-pattern 502567301[1-9]
>>  direct-inward-dial
>>  port 1/0:24:20
>>  forward-digits all****
>>
>>  ****
>>
>> On the IAD2400****
>>
>>  ****
>>
>> controller T1 0/0
>>  mode cas
>>  framing esf
>>  linecode b8zs
>>  channel-group 0 timeslots 1-20 speed 64
>>  ds0-group 20 timeslots 21-24 type fxo-ground-start
>> !
>> interface Serial0/0:0
>>  ip address 216.24.2.6 255.255.255.252
>> !
>> voice-port 0/0:20
>> !
>> voice-port 2/0
>>  station-id number 5025673011
>> !
>> dial-peer voice 10 pots
>>  incoming called-number 5025673011
>>  direct-inward-dial
>>  port 2/0
>>  forward-digits all ****
>>
>> ** **
>>
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20120708/1b8c7a9f/attachment.html>