[cisco-voip] Calls to DS-'s across channelized T1, no calling number at CPE

[Paul]

slight technicality - if they were using a hardware FXS/DID port as a dedicated inbound DID port then they'd be able to use direct-inward-dial...
not just for PRIs...


________________________________
From: Nick Matthews <matthnick at gmail.com>
To: Jonathan Charles <jonvoip at gmail.com> 
Cc: cisco-voip <cisco-voip at puck.nether.net> 
Sent: Sunday, July 8, 2012 9:45 PM
Subject: Re: [cisco-voip] Calls to DS-'s across channelized T1, no calling number at CPE


Couple things, not sure of any of these will solve the problem:
-Remove 'direct-inward-dial' on the FXS port. Only for PRI's.
-Need to enable caller ID on FXS. 'caller-id enable' on voice-port 2/0
-May also need caller-id on voice-port 1/0:24 also.

-nick


On Fri, Jul 6, 2012 at 11:43 PM, Jonathan Charles <jonvoip at gmail.com> wrote:

I am lazy, I would just back to back PRI it...
>
>
>
>
>
>
>
>Jonathan
>
>
>
>On Fri, Jul 6, 2012 at 10:01 PM, Southeasttexas Telecom <SETXTelecom at att.net> wrote:
>
>He’ll need to change the type on the IAD to FXS as well but isn’t there a tie or similar setting that would better match what he is doing (and used on both ends)?…….Using Ground start ? I would set it to Wink Start if available.
>> 
>>From:cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Jonathan Charles
>>Sent: Friday, July 06, 2012 8:21 PM
>>To: Joseph Mays
>>Cc: cisco-voip at puck.nether.net
>>Subject: Re: [cisco-voip] Calls to DS-'s across channelized T1, no calling number at CPE
>> 
>>They are set to FXS, they won't send digits... (it is acting like a station port...)
>> 
>>You will need to set them to FGD or FXO...
>> 
>>ds0-group 0 timeslots 1-2 type fgd-eana
>> 
>> 
>> 
>>Jonathan
>> 
>>On Fri, Jul 6, 2012 at 1:18 PM, Joseph Mays <mays at win.net> wrote:
>>I'm configuring an AS5400 to provide a channelized t1 to an IAD2400. 4 of the channels on the T1 are being used for a DS0 group across which we want the AS5400 to handle voice calls to and from the IAD2400.
>> 
>>On the AS5400
>> 
>>controller T1 1/0:24
>> framing esf
>> channel-group 0 timeslots 1-20 speed 64
>> loopback network ignore
>> ds0-group 20 timeslots 21-24 type fxs-ground-start
>>!
>>interface Serial1/0:24:0
>> ip address 216.24.2.5 255.255.255.252
>> no cdp enable
>>!
>>voice-port 1/0:24:20
>>!
>>dial-peer voice 248 pots
>> description ATA-8 TEST line 2, WinNETPBX
>> incoming called-number 502567301[1-9]
>> destination-pattern 502567301[1-9]
>> direct-inward-dial
>> port 1/0:24:20
>> forward-digits all
>> 
>>On the IAD2400
>> 
>>controller T1 0/0
>> mode cas
>> framing esf
>> linecode b8zs
>> channel-group 0 timeslots 1-20 speed 64
>> ds0-group 20 timeslots 21-24 type fxo-ground-start
>>!
>>interface Serial0/0:0
>> ip address 216.24.2.6 255.255.255.252
>>!
>>voice-port 0/0:20
>>!
>>voice-port 2/0
>> station-id number 5025673011
>>!
>>dial-peer voice 10 pots
>> incoming called-number 5025673011
>> direct-inward-dial
>> port 2/0
>> forward-digits all 
>> 
>>
>>_______________________________________________
>>cisco-voip mailing list
>>cisco-voip at puck.nether.net
>>https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>
>_______________________________________________
>cisco-voip mailing list
>cisco-voip at puck.nether.net
>https://puck.nether.net/mailman/listinfo/cisco-voip
>
>

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip