[cisco-voip] ATA 188's and CUCM 8.6.2

[Erick B.]

Thanks all. Got this figured out.

For some reason, both ports on the ATA config got disabled to during
migration of CCM versions. Had to set both ports back to . and they
registered, had to do manual upgrade procedure to with modifying the
XML file. The main reason why they weren't registering was the ports
getting set to 0 (disabled) somehow. Haven't seen that before. I've
seen the ATAs or phones stuck on old firmware but still working.

On Thu, Oct 18, 2012 at 11:51 PM, Buchanan, James
<jbuchanan at presidio.com> wrote:
> You can put it back to more than one server now that you're on 3.2.4. I'd check that server side first and go from there
>
>
> James Buchanan | Sr. Network Engineer
> Presidio | www.presidio.com
> 12 Cadillac Drive Suite 130, Brentwood, TN 37027
> D: 615.866.5729 | C: 931.797.2326 | F: 615.866.5781 | jbuchanan at presidio.com
>
>
>
> PRESIDIO
>
>
> Follow Us: www.twitter.com/presidio
>
> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Erick B.
> Sent: Thursday, October 18, 2012 10:11 PM
> To: Jason Aarons (AM)
> Cc: voip puck
> Subject: Re: [cisco-voip] ATA 188's and CUCM 8.6.2
>
> Hi,
>
> I did get the ATA 188 upgraded to 3.2.4 and it registered briefly but now is unregistered again.  They still show up / set up as ATA 186s in CUCM right (don't see a device for ATA 188).  I have some slow response issues on the server side I'm looking at, so I think the ATA
> 188 is good now that it is on 3.2.4 and it registered briefly.  I did reduce the CMGroup down to 1 call manager server also.
>
> I'll post update once I get these registered and they stay up. If anyone has any ideas, I'm all ears.
>
> Thanks.
>
> On Thu, Oct 18, 2012 at 12:31 PM, Jason Aarons (AM) <jason.aarons at dimensiondata.com> wrote:
>> You have to reduce the number of CMs in the CMG to 2 to get below 4k,
>> then you can upgrade.
>>
>>
>>
>> From: cisco-voip-bounces at puck.nether.net
>> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Nate VanMaren
>> Sent: Thursday, October 18, 2012 12:31 PM
>> To: Erick B.; voip puck
>> Subject: Re: [cisco-voip] ATA 188's and CUCM 8.6.2
>>
>>
>>
>>
>>
>> They work, but you have to get them to a firmware version that can
>> handle the new bigger configuration files (or something along those
>> lines)
>>
>> -nate
>>
>> -----Original Message-----
>> From: cisco-voip-bounces at puck.nether.net
>> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Erick B.
>> Sent: Thursday, October 18, 2012 10:27 AM
>> To: voip puck
>> Subject: [cisco-voip] ATA 188's and CUCM 8.6.2
>>
>> Do ATA 188s work on 8.6.2 SU2a? Had a couple dozen working on older
>> CCM Version and upgraded to 8.62 and they are not registering. I found
>> document that shows support up to 8.0 and searched google, etc and
>> finding a few hits but no real answers as to if they work or not. The
>> couple hits I found on cisco support forums didn't have any replies.
>>
>> The ATA's have 3.2.3 firmware on them.
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>> itevomcid
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
> This message w/attachments (message) is intended solely for the use of the intended recipient(s) and may contain information that is privileged, confidential or proprietary. If you are not an intended recipient, please notify the sender, and then please delete and destroy all copies and attachments. Please be advised that any review or dissemination of, or the taking of any action in reliance on, the information contained in or attached to this message is prohibited.
>