[cisco-voip] Router as H323 GW and also as SIP GW

[Anthony Holloway]

Here's a good starting document on CUBE.  It even covers IOS versions and
licensing:
http://www.cisco.com/en/US/docs/ios/voice/cube/configuration/guide/vb_ch1_ps5640_TSD_Products_Configuration_Guide_Chapter.html




On Thu, Oct 3, 2013 at 10:50 AM, vignesh sethuraman <
sethuvignesh at yahoo.co.in> wrote:

> Hello Anthony,
>
> Thanks alot for your prompt response.
>
> My Router is running, Cisco IOS Software, 7200 Software
> (C7200P-ADVENTERPRISEK9-M), Version 12.4(24)T1, RELEASE SOFTWARE (fc3).
>
> Is it possible to enable CUBE (With Honor based License) on 7206VXR
> running Version 12.4(24)T1?
>
> Thanks,
> Vik
> ****
>
>   ------------------------------
>  *From:* Anthony Holloway <avholloway+cisco-voip at gmail.com>
> *To:* vignesh sethuraman <sethuvignesh at yahoo.co.in>
> *Cc:* "cisco-voip at puck.nether.net" <cisco-voip at puck.nether.net>
> *Sent:* Thursday, 3 October 2013 5:39 PM
>
> *Subject:* Re: [cisco-voip] Router as H323 GW and also as SIP GW
>
> CUBE is an IP-to-IP gateway, and so H323-to-SIP qualifies as such, and
> therefore requires CUBE.  However, CUBE licensines is honor based, so
> technically you could run CUBE without the licenses.
>
>
> On Thu, Oct 3, 2013 at 10:27 AM, vignesh sethuraman <
> sethuvignesh at yahoo.co.in> wrote:
>
> Dear All,
>
> If I am using H323 to SIP, do I need a CUBE License for this to be
> uploaded to 7206VXR Router. Here is my scenario
>
>
> CUCM -----H.323 Trunk-------7206VXR-------SIP------- CUBE
>
> Thanks,
> Viki
>
>   ------------------------------
>  *From:* Anthony Holloway <avholloway+cisco-voip at gmail.com>
> *To:* vignesh sethuraman <sethuvignesh at yahoo.co.in>
> *Cc:* "cisco-voip at puck.nether.net" <cisco-voip at puck.nether.net>
> *Sent:* Tuesday, 1 October 2013 7:52 PM
> *Subject:* Re: [cisco-voip] Router as H323 GW and also as SIP GW
>
> I should have been more clear that there are a number of other commands
> you should configure on your gateway as it pertains to SIP best practices
> and interoperability, however I was simply stating the bare minimum command
> to switch the protocol from H323 to SIP.
>
> Example of other commands you may want to look into (not a comprehensive
> list):
>
> voice service voip
>  sip
>   bind control source-interface <your interface>
>   bind media source-interface <your interface>
>
> dial-peer voice XXX voip
>  dtmf-relay sip-notify rtp-nte digit-drop
>
> Also, if you need to tweak SIP timers or retry counters you will need to
> use the: sip-au section and then use the: session target sip-server command.
>
> Hope that helps.
>
>
> On Tue, Oct 1, 2013 at 12:35 PM, Anthony Holloway <
> avholloway+cisco-voip at gmail.com> wrote:
>
> A voice gateway has H.323 enabled by default, and as such, your voip
> dialpeers are H323 unless you tell it otherwise.
>
> How you switch from H323 to SIP on a per dialpeer basis, is with the
> dialpeer command:  session protocol sipv2
>
> By doing it per dialpeer you are able to run in a mixed SIP/H323
> environment.
>
> If you're going from TDM to SIP on your 7206, then that is all you need.
> If you are doing H323 to SIP or SIP to SIP then you'll need the appropriate
> allow connection commands under voice service voip.  But since you
> mentioned CUBE, I assume you're already familiar with these commands.
>
>
> On Tue, Oct 1, 2013 at 10:21 AM, vignesh sethuraman <
> sethuvignesh at yahoo.co.in> wrote:
>
> Hello Experts,
>
> I have a 7206 router acting as H323 GW registered to a CUCM. Along with
> that, I need to create a SIP trunk on the same router to a CUBE.
>
> Please let me know if it is possible or not. And also do let me know if
> something needs to be taken care.
>
> Thanks,
> Viki
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
>
>
>
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20131003/73d0d189/attachment.html>