[cisco-voip] SX20 Telepresence software upgrade

[Chris Ward (chrward)]

James,

It's also possible that the load they running while CUCM compatible weren't yet capable of downloading firmware from CUCM. I am not sure in the history of TC code where that capability was added.

+Chris
TME - Unity Connection and MediaSense

From: James Dust [mailto:james.dust at charles-stanley.co.uk]
Sent: Wednesday, September 11, 2013 12:04 PM
To: Chris Ward (chrward); cisco-voip at puck.nether.net
Subject: RE: SX20 Telepresence software upgrade

Afternoon Chris,

Yes I have restarted the TFTP service on all nodes, and it was a cop file I used to upload the firmware.

The device defaults page has been updated and no specific phone load is specified on the devices themselves.

Thanks for sanity checking this for me, I may need to log a support case now then.

Kind Regards

James

From: Chris Ward (chrward) [mailto:chrward at cisco.com]
Sent: 11 September 2013 16:54
To: James Dust; cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Subject: RE: SX20 Telepresence software upgrade

Hi James,

Have you started TFTP on the TFTP server? That would be required after a cop file install or manual file upload to the TFTP directory.

Also, check the device defaults for the SX20 and see if there is a version specified, if not, specify one. A COP file installation should have done this for you, but a manual upload would not. Also, make sure that a firmware load is NOT defined on the device's page itself (ccmadmin) as this will override the device default page.

That is my normal list of things to check/do for phones that aren't upgrading as expected.

+Chris
TME - Unity Connection and MediaSense

From: cisco-voip [mailto:cisco-voip-bounces at puck.nether.net]<mailto:[mailto:cisco-voip-bounces at puck.nether.net]> On Behalf Of James Dust
Sent: Wednesday, September 11, 2013 11:06 AM
To: cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Subject: [cisco-voip] SX20 Telepresence software upgrade

Afternoon all,

I am trying to upgrade some SX20 devices on our 8.6.2 cucm cluster from version TC5.1.5 to TC6.1.1 but am encountering difficulties. I have installed the new software on all cucm nodes and hard reset/factory reset the SX20's to try and get them to upgrade but they don't pick up the new default software image.

Has anyone else encountered this problem? And if so what do you need to do?

On a side note I realise you need to update the release key for the device when you upgrade and have this covered.

Kind regards

James

Consider the environment - Think before you print

The contents of this email are confidential to the intended recipient and may not be disclosed. Although it is believed that this email and any attachments are virus free, it is the responsibility of the recipient to confirm this.

You are advised that urgent, time-sensitive communications should not be sent by email. We hereby give you notice that a delivery receipt does not constitute acknowledgement or receipt by the intended recipient(s).

Details of Charles Stanley group companies and their regulators (where applicable), can be found at this URL http://www.charles-stanley.co.uk/contact-us/disclosure/

Consider the environment - Think before you print

The contents of this email are confidential to the intended recipient and may not be disclosed. Although it is believed that this email and any attachments are virus free, it is the responsibility of the recipient to confirm this.

You are advised that urgent, time-sensitive communications should not be sent by email. We hereby give you notice that a delivery receipt does not constitute acknowledgement or receipt by the intended recipient(s).

Details of Charles Stanley group companies and their regulators (where applicable), can be found at this URL http://www.charles-stanley.co.uk/contact-us/disclosure/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20130911/70014131/attachment.html>