[cisco-voip] Caller ID issue

[David Zhars]

IOS is 15.0.(1)M4
UCM is 8.0

I think you all are right about converting to H323

On Wed, Feb 3, 2016 at 12:54 PM, Brian Meade <bmeade90 at vt.edu> wrote:

> Some people claim it works okay with MGCP as long as you're on CUCM 8.x
> and higher above a certain IOS version.  It's definitely easier to just
> switch to H.323 or SIP though.
>
> On Wed, Feb 3, 2016 at 12:49 PM, Ryan Huff <ryanhuff at outlook.com> wrote:
>
>> You'll need to CFG the gateway as h.323 (at least for that FXO port).
>> CLID doesn't work on FXO ports controlled by mgcpapp . You can run a "*debug
>> vpm port x/x/x*" and that should show the calling name received on the
>> FXO port, but if the port is under mgcpapp control, it won't pass the IE to
>> CCM.
>>
>>
>> Thanks,
>>
>>
>> = Ryan =
>>
>>
>>
>> Email: ryanthomashuff at outlook.com
>>
>> Spark: ryanthomashuff at outlook.com
>>
>> Twitter: @ryanthomashuff <http://twitter.com/ryanthomashuff>
>>
>> LinkedIn: ryanthomashuff <http://linkedin.com/in/ryanthomashuff>
>>
>> Web ryanthomashuff.com
>>
>>
>> ------------------------------
>> *From:* cisco-voip <cisco-voip-bounces at puck.nether.net> on behalf of
>> Brian Meade <bmeade90 at vt.edu>
>> *Sent:* Wednesday, February 3, 2016 12:38 PM
>> *To:* David Zhars
>> *Cc:* cisco-voip at puck.nether.net
>> *Subject:* Re: [cisco-voip] Caller ID issue
>>
>> What CUCM/IOS version?  Do you have "Enable Caller ID" checked on the
>> MGCP FXO device?  You should have "caller-id enable" under the voice-port
>> on the router.
>>
>> http://www.gossamer-threads.com/lists/cisco/voip/131620
>>
>> On Wed, Feb 3, 2016 at 12:28 PM, David Zhars <dzhars at gmail.com> wrote:
>>
>>> Sorry, just noticed in that example they reference ISDN.  Again, calls
>>> coming in on ISDN are fine, we get name and number.
>>> It's when calls come in on the POTS lines that we just get the phone
>>> number.
>>>
>>> On Wed, Feb 3, 2016 at 12:27 PM, David Zhars <dzhars at gmail.com> wrote:
>>>
>>>> ISDN works fine.  It's when the calls come in on the POTS line.
>>>>
>>>> I did find this by googling:
>>>>
>>>> interface serialx/x/x:23
>>>> isdn supp-service name calling
>>>>
>>>> I am not sure about the :23 after the serial port designation...
>>>>
>>>>
>>>> On Wed, Feb 3, 2016 at 12:23 PM, Brian Meade <bmeade90 at vt.edu> wrote:
>>>>
>>>>> Does the carrier send the caller name in the ISDN Setup message or in
>>>>> a separate Facility message?  Can you show "debug isdn q931" for one of
>>>>> these inbound calls?
>>>>>
>>>>> On Wed, Feb 3, 2016 at 12:13 PM, David Zhars <dzhars at gmail.com> wrote:
>>>>>
>>>>>> Cisco UCM 8.0 with 2801 in MGCP mode.
>>>>>> Telco is sending Name and Number to us.
>>>>>> Phones only ever display Number.
>>>>>>
>>>>>> In UCM, selected phones have both Caller Name and Caller Number
>>>>>> ticked.
>>>>>>
>>>>>> Anything else could be preventing us from getting Names?
>>>>>>
>>>>>> _______________________________________________
>>>>>> cisco-voip mailing list
>>>>>> cisco-voip at puck.nether.net
>>>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20160203/29a634a2/attachment.html>