[cisco-voip] DX80 issues.

[Brian Meade]

Option 150 is all you need to worry about for TFTP downloads.

On Fri, Jun 16, 2017 at 3:38 AM, naresh rathore <nareh84 at hotmail.com> wrote:

> i will check option 150 later, but cucmsub is preferred in cucm group
> (devicepool)
>
>
> ------------------------------
> *From:* bmeade90 at gmail.com <bmeade90 at gmail.com> on behalf of Brian Meade <
> bmeade90 at vt.edu>
> *Sent:* Friday, June 16, 2017 12:19 PM
>
> *To:* naresh rathore
> *Cc:* cisco-voip at puck.nether.net
> *Subject:* Re: [cisco-voip] DX80 issues.
>
> It just depends on what the DX80 is pointed at.  If it's set to use the
> pub as TFTP server 1 then you're fine.
>
> On Fri, Jun 16, 2017 at 3:12 AM, naresh rathore <nareh84 at hotmail.com>
> wrote:
>
>> is it necessary to active tftp service on cucm-sub? or
>>
>>
>>
>> when i point it to cucmpub. i succesfuly downloaded the file using tftp.
>> but when i pointed it to cucmsub, the file was 0byte, not successfully
>> downloaded (because tftp is not enabled on cucmsub.
>>
>>
>>
>> Regards
>>
>>
>>
>> Naray
>>
>>
>> ------------------------------
>> *From:* bmeade90 at gmail.com <bmeade90 at gmail.com> on behalf of Brian Meade
>> <bmeade90 at vt.edu>
>> *Sent:* Friday, June 16, 2017 11:38 AM
>> *To:* naresh rathore
>> *Cc:* cisco-voip at puck.nether.net
>> *Subject:* Re: [cisco-voip] DX80 issues.
>>
>> You can try restarting TFTP.  Also see if you can download the .loads
>> file with a TFTP Client.
>>
>> On Fri, Jun 16, 2017 at 2:13 AM, naresh rathore <nareh84 at hotmail.com>
>> wrote:
>>
>>> hi,
>>>
>>>
>>>
>>> I am facing two issues with DX80.
>>>
>>>
>>>
>>>
>>>    1. First, video call is not successful with DX80. when i check self
>>>    view (while not on call).there is nothing. so i think there can be issue
>>>    with the camera. video call is enabled on Device > Phone and between video
>>>    and phone device pool, the codec is G711, maximum session bit rate for
>>>    video calls: 384kbps, maximum session bit rate for immersive video calls:
>>>    1024kbps
>>>
>>>
>>>
>>>       2. Second, is the upgrade (may be upgrade will resolve camera
>>> issue) . Currently DX80 is on android firmware and the required firmware is
>>> also android. I use ftp/sftp to upload the file on both cucm, on one cucm
>>> tftp service is active while on another cucm (sub), tftp is not active but
>>> i uploaded file on both of them and can see the .load file on tftp file
>>> management. but see the following status after upgrade (upgrade failed).
>>>
>>>
>>> *Registration:* Registered with Cisco Unified Communications Manager
>>> CUCM02
>>> *IPv4 Address:* x.x.x.x <http://10.163.167.14/>
>>> *Active Load ID:* sipdx80.10-2-2-23
>>> *Inactive Load ID:* INVALID
>>> *Download Status:* Failed
>>> *Requested Load ID:* sipdx80.10-2-4-99
>>> *Download Server:* 10.163.72.100
>>> Inactive Load Failure Reason File Not Found
>>> Any suggestions.
>>>
>>>
>>> _______________________________________________
>>> cisco-voip mailing list
>>> cisco-voip at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>
>>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20170616/22a53d3f/attachment.html>