[cisco-voip] ISDN T1 voice calls hardware validation

[Ryan Huff]

Not sure if DSP is onboard the SPA like the NIM; I’d have to look that one up ... you might try dsp services dspfarm under the voice-card configuration parameter. I’d also disable cdp on the serial interface.

Sent from my iPhone

On May 4, 2018, at 12:18, PF <pucknether at foril.com<mailto:pucknether at foril.com>> wrote:

Hi

I have tried several configurations

Here is the relevent par of the actual config

version 15.3
boot system flash bootflash:asr1000rp2-adventerprisek9.03.10.07.S.153-3.S7-ext.bin
!
card type t1 0 2
!
multilink bundle-name authenticated
isdn switch-type primary-5ess
!
voice-card 0/0
!
voice service pots
 supported-language FR
!
voice service voip
 clid network-provided
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 signaling forward unconditional
 sip
  bind control source-interface GigabitEthernet1/2/0
  bind media source-interface GigabitEthernet1/2/0
  ds0-num
  header-passing
  privacy id
  outbound-proxy ipv4:172.16.x.y
!
voice class codec 1
 codec preference 1 g711ulaw
!
controller T1 0/2/0
 framing esf
 clock source internal
 linecode b8zs
 cablelength long 0db
 pri-group timeslots 1-24
!
interface Service-Engine0/0/0
!
interface Serial0/2/0:23
 encapsulation hdlc
 isdn switch-type primary-5ess
 isdn negotiate-bchan
!
map-class dialer DOVtest
 dialer voice-call
!
dspfarm profile 1 transcode universal
 rsvp
 shutdown
!
dial-peer voice 1 voip
 destination-pattern *.
 signaling forward unconditional
 session protocol sipv2
 session target sip-server
 voice-class codec 1
!
dial-peer voice 2 pots
 destination-pattern xxxxxxx
 incoming called-number xxxxxxx
 direct-inward-dial
!
!
sip-ua
 credentials username asr1006 password 7 xxxxxxxx realm yyyyy
 retry invite 3
 retry bye 3
 retry cancel 3
 timers trying 1000
 timers register 100
 sip-server ipv4:172.16.x.y
!
!
Pat


----- Original Message -----
From: Ryan Huff<mailto:ryanhuff at outlook.com>
To: Patrick Fortin<mailto:pfortin at royaume.com>
Cc: cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Sent: Friday, May 04, 2018 11:43 AM
Subject: Re: [cisco-voip] ISDN T1 voice calls hardware validation

I assume you have the card type specified and controller interface configured with timeslots?

Can you send the running-config and code version?

Sent from my iPhone

On May 4, 2018, at 11:35, Patrick Fortin <pfortin at royaume.com<mailto:pfortin at royaume.com>> wrote:

Hi

I get this error

 **ERROR**: call_incoming: Received a call id 0x2F with a bad bearercap from xxxxxxxxxx on b channel 1

seems like the dsp are not associated with the t1 card

in the config we don't have acces to the following :

isdn incoming-voice voice
which should go on the Serial interface.

we also don't have the "port" command that should go in the dial-peer voice section

any ideas ?

Thanks

Pat
----- Original Message -----
From: Ryan Huff<mailto:ryanhuff at outlook.com>
To: PF<mailto:pucknether at foril.com>
Cc: cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Sent: Friday, May 04, 2018 11:11 AM
Subject: Re: [cisco-voip] ISDN T1 voice calls hardware validation

That correct! I misread! Yeah the shared port adapter T1 should work.


Sent from my iPhone

On May 4, 2018, at 10:36, PF <pucknether at foril.com<mailto:pucknether at foril.com>> wrote:

Hi

Thanks for your help

But there are no NIM slot in the ASR1006 chassis

NIM is for ASR1001-X I think

Pat

----- Original Message -----
From: Ryan Huff<mailto:ryanhuff at outlook.com>
To: PF<mailto:pucknether at foril.com>
Cc: cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Sent: Friday, May 04, 2018 9:56 AM
Subject: Re: [cisco-voip] ISDN T1 voice calls hardware validation

For isdn voice you’ll need a NIM-8MFT-T1/E1

Sent from my iPhone

On May 4, 2018, at 09:31, PF <pucknether at foril.com<mailto:pucknether at foril.com>> wrote:

Hi

Can someone help us validate if we can use this hardware to receive voice calls from a isdn T1 (23B+D) and send them in SIP to a softswitch and vice-versa

ASR1006
SPA-8XCHT1/E1
SPA-DSP
ASR1000-RP2
ASR1000-ESP40

in short can it be used to build a voip gateway like an audiocode mediant or a patton smartnode

Thanks

Pat

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
https://puck.nether.net/mailman/listinfo/cisco-voip
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20180504/1ab03bbe/attachment.html>