[e-nsp] Summit 400-48t Port Problems

Fri Aug 29 17:39:46 EDT 2008

I ran a 'run diag extended' everything passed see output:

* Summit400-48t:8 # run diag extended

Running Extended diagnostics will reset the switch and disrupt network
traffic.

Are you sure you want to continue?  yes/no yes
The configuration database has been changed (primary configuration is
selected).
Do you wish to save these changes (yes, no, or cancel) yes
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>!.!.!System will reset in 2 seconds

Power On Self Test ... OK

Boot Module, Jul 19 2004 v4.9
=============================
Memory Size: 256 MB

Press spacebar during powercycle for boot menu

Decompressing primary image from flash to ram
....................................+..................................
.................................................................!

Starting Summit400 extended diagnostic test...
Start cpu diagnostic test... ... ... ... ... ... ..... ... ....PASSED
Start switch ASIC diagnostic test... ..... ..... .....PASSED

CPU Loopback Test
Device.............................................................................................
......0(13).....1(13).....2(13).....3(13).....PASSED
Port 1000BaseT MAC loopback test...
.................................................................................
...............1....................2....................3....................4....................5.................
...6....................7....................8....................9....................10....................11......
..............12....................13....................14....................15....................16.............
.......17....................18....................19....................20....................21....................
22....................23....................24....................25....................26....................27.....
...............28....................29....................30....................31....................32............
........33....................34....................35....................36....................37...................
.38....................39....................40....................41....................42....................43....
................44....................45....................46....................47....................48...........
.........PASSED
Port 10BaseT PHY loopback test...
...................................................................................
.............1.....2.....3.....4.....5.....6.....7.....8.....9.....10.....11.....12.....13.....14.....15.....16.....1
7.....18.....19.....20.....21.....22.....23.....24.....25.....26.....27.....28.....29.....30.....31.....32.....33....
.34.....35.....36.....37.....38.....39.....40.....41.....42.....43.....44.....45.....46.....47.....48.....PASSED
Port 100BaseT PHY loopback test...
..................................................................................
..............1.....2.....3.....4.....5.....6.....7.....8.....9.....10.....11.....12.....13.....14.....15.....16.....
17.....18.....19.....20.....21.....22.....23.....24.....25.....26.....27.....28.....29.....30.....31.....32.....33...
..34.....35.....36.....37.....38.....39.....40.....41.....42.....43.....44.....45.....46.....47.....48.....PASSED
Port 1000BaseT PHY loopback test...
.................................................................................
...............1.....2.....3.....4.....5.....6.....7.....8.....9.....10.....11.....12.....13.....14.....15.....16....
.17.....18.....19.....20.....21.....22.....23.....24.....25.....26.....27.....28.....29.....30.....31.....32.....33..
...34.....35.....36.....37.....38.....39.....40.....41.....42.....43.....44.....45.....46.....47.....48.....PASSED
Internal HiGig Port Link Test Device... 0...1...2...3...PASSED

Power On Self Test ... OK

Boot Module, Jul 19 2004 v4.9
=============================
Memory Size: 256 MB

Press spacebar during powercycle for boot menu

Decompressing primary image from flash to ram
....................................+..................................
.................................................................!

Version 7.3e.0.43 [non-ssh] by Release_Master on 09/17/04 00:46:11
System Serial Number: xxxxxxxx
Memory Size: 268435456 (256MB)!
login:

RootNet08

On Fri, Aug 29, 2008 at 4:08 AM, Fabian <fabian.extr at gmail.com> wrote:

>  Hi,
>
>
>
> You have to configure an ip@ to the MGMT VLAN (that have 1 unique port :
> the management outband port) :
>
> Configure mgmt ipaddress x.x.x.x/x
>
>
>
> I would suggest to run a diag on your switch to verify that there is
> nothing wrong with the hardware after the power failure.
>
>
>
> Regards.
>
>
>
> *From:* extreme-nsp-bounces at puck.nether.net [mailto:
> extreme-nsp-bounces at puck.nether.net] *On Behalf Of *root net
> *Sent:* vendredi 29 août 2008 06:09
> *To:* extreme-nsp at puck.nether.net
> *Subject:* [e-nsp] Summit 400-48t Port Problems
>
>
>
> Hello,
>
> I have checked the archives from 2003 to now and could not find this
> anywhere.  Here is my problem:
>
> I have a Extreme Summit 400-48t lost power for about 5-12 secs (UPS
> failure/problem) but powered back on after power was restored and none of
> the ports worked.  I have an exact copy of this switch running as well and
> it fired back up without a problem unlike this one.
>
> Here are sample logs:
>
> 09/26/2007 16:11:34.23 <Erro> <EDP.ProcPDUFail> pdu received on port 2
> could not be processed, checksum error on port 2
> 09/25/2007 11:10:18.43 <Erro> <EDP.ProcPDUFail> pdu received on port 2
> could not be processed, checksum error on port 2
> 09/25/2007 10:20:02.55 <Erro> <EDP.ProcPDUFail> pdu received on port 2
> could not be processed, checksum error on port 2
> 09/24/2007 23:50:41.30 <Erro> <EDP.ProcPDUFail> pdu received on port 2
> could not be processed, checksum error on port 2
> 09/20/2007 13:43:49.85 <Erro> <EDP.ProcPDUFail
>
> BTW I wiped the config and the time is off now so ignore that.
>
> What do you think is wrong? How can I procure? I thought about reloading
> the image but can not use the ports to do a tftp. Can some one explain also
> how to configure the management port on the back to do this if possible.  I
> am a Cisco person not extreme but I am learning.
>
> Thanks in advanced!!!
>
> --RootNet08
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/extreme-nsp/attachments/20080829/baf9c431/attachment.html>