[f-nsp] Port State Blocking, FastIron SX 800
Jared Valentine
hidden at xmission.com
Wed Sep 30 16:00:45 EDT 2009
Upgrading to 5.1.00b should fix this problem.
Closed defects in IronWare R05.1.00b for the FastIron X Series Switches
106289 Critical Summary: 10 GbE ports may not link up.
Symptom: No link on 10 GbE ports
Probability: Medium
Feature: System
Function: System
Jared Valentine
hidden at xmission.com
From: foundry-nsp-bounces at puck.nether.net
[mailto:foundry-nsp-bounces at puck.nether.net] On Behalf Of Chuck Ufarley
Sent: Wednesday, September 30, 2009 12:58 PM
To: foundry-nsp at puck.nether.net
Subject: [f-nsp] Port State Blocking, FastIron SX 800
Hi all--
I've got an FI-SX 800 with a FI-2XGMR4 PREM and a couple of FI-42XGs, and I
can't seem to get the ports on the 2XGs to come up. There's nothing
connected to the box at all. Reloads and power downs keep repeating a port
state BLOCKING. Can't figure out why. Console output is below. Anyone got
any advice?
FastIron SX 800 Router#sho run
Current configuration:
!
ver 05.1.00T3e3
!
module 1 fi-sx4-2-port-10g-module
module 2 fi-sx4-2-port-10g-module
module 9 fi-sx4-2-10g-port-management-module
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
end
FastIron SX 800 Router#sho ver
==========================================================================
Active Management CPU [Slot-9]:
SW: Version 05.1.00T3e3 Copyright (c) 1996-2009 Brocade Communications
Systems
, Inc.
Compiled on May 12 2009 at 22:13:55 labeled as SXR05100
(3395303 bytes) from Primary SXR05100.bin
BootROM: Version 05.1.00T3e5 (FEv2)
Serial #: SA17085232
HW: Chassis FastIron SX 800-PREM (PROM-TYPE SX-FIL3U)
==========================================================================
SL 1: SX-FI42XG 2-port 10G
Serial #: CH05080069
P-ASIC 0: type 01D1, rev 00 subrev 00
P-ASIC 1: type 01D1, rev 00 subrev 00
==========================================================================
SL 2: SX-FI42XG 2-port 10G
Serial #: CH05080080
P-ASIC 2: type 01D1, rev 00 subrev 00
P-ASIC 3: type 01D1, rev 00 subrev 00
==========================================================================
SL 9: SX-FI2XGMR4 2-port Management
Serial #: CH34070027
P-ASIC 16: type 01D1, rev 00 subrev 00
P-ASIC 17: type 01D1, rev 00 subrev 00
==========================================================================
Active Management Module:
660 MHz Power PC processor 8541 (version 32/0020) 66 MHz bus
512 KB boot flash memory
16384 KB code flash memory
512 MB DRAM
The system uptime is 22 minutes 9 seconds
The system : started=cold start
FastIron SX 800 Router#sho mod
Module Status Ports Starting MAC
F1: SX-FISF Switch Fabric active
F2: SX-FISF Switch Fabric active
S1: SX-FI42XG 2-port 10G OK 2 0012.f226.d700
S2: SX-FI42XG 2-port 10G OK 2 0012.f226.d718
S3:
S4:
S5:
S6:
S7:
S8:
S9: SX-FI2XGMR4 2-port Management Active 2 0012.f226.d7c0
{ Status : OK }
S10: Standby 0
FastIron SX 800 Router#sho int e 1/1
10GigabitEthernet1/1 is down, line protocol is down
Hardware is 10GigabitEthernet, address is 0012.f226.d700 (bia
0012.f226.d700)
Configured speed 10Gbit, actual unknown, configured duplex fdx, actual
unknown
Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING
BPDU guard is Disabled, ROOT protect is Disabled
Link Error Dampening is Disabled
STP configured to ON, priority is level0
Flow Control is enabled
mirror disabled, monitor disabled
Not member of any active trunks
Not member of any configured trunks
No port name
IPG XGMII 96 bits-time
IP MTU 1500 bytes, encapsulation ethernet
300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 multicasts, 0 unicasts
0 input errors, 0 CRC, 0 frame, 0 ignored
0 runts, 0 giants
0 packets output, 0 bytes, 0 underruns
Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
0 output errors, 0 collisions
Relay Agent Information option: Disabled
FastIron SX 800 Router#sho int e 1/2
10GigabitEthernet1/2 is down, line protocol is down
Hardware is 10GigabitEthernet, address is 0012.f226.d701 (bia
0012.f226.d701)
Configured speed 10Gbit, actual unknown, configured duplex fdx, actual
unknown
Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING
BPDU guard is Disabled, ROOT protect is Disabled
Link Error Dampening is Disabled
STP configured to ON, priority is level0
Flow Control is enabled
mirror disabled, monitor disabled
Not member of any active trunks
Not member of any configured trunks
No port name
IPG XGMII 96 bits-time
IP MTU 1500 bytes, encapsulation ethernet
300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 multicasts, 0 unicasts
0 input errors, 0 CRC, 0 frame, 0 ignored
0 runts, 0 giants
0 packets output, 0 bytes, 0 underruns
Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
0 output errors, 0 collisions
Relay Agent Information option: Disabled
FastIron SX 800 Router#
As always, your help is greatly appreciated.
Thanks.
--Chuck
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/foundry-nsp/attachments/20090930/8f640d40/attachment.html>
More information about the foundry-nsp
mailing list