[f-nsp] Port State Blocking, FastIron SX 800

[Chuck Ufarley]

Hi all--

I've got an FI-SX 800 with a FI-2XGMR4 PREM and a couple of FI-42XGs, and I
can't seem to get the ports on the 2XGs to come up.  There's nothing
connected to the box at all.  Reloads and power downs keep repeating a port
state BLOCKING.  Can't figure out why.  Console output is below.  Anyone got
any advice?

FastIron SX 800 Router#sho run
Current configuration:
!
ver 05.1.00T3e3
!
module 1 fi-sx4-2-port-10g-module
module 2 fi-sx4-2-port-10g-module
module 9 fi-sx4-2-10g-port-management-module
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
end

FastIron SX 800 Router#sho ver

==========================================================================
Active Management CPU [Slot-9]:
  SW: Version 05.1.00T3e3 Copyright (c) 1996-2009 Brocade Communications
Systems
, Inc.
      Compiled on May 12 2009 at 22:13:55 labeled as SXR05100
      (3395303 bytes) from Primary SXR05100.bin
      BootROM: Version 05.1.00T3e5 (FEv2)
      Serial  #: SA17085232
  HW: Chassis FastIron SX 800-PREM (PROM-TYPE SX-FIL3U)
==========================================================================
SL 1: SX-FI42XG 2-port 10G
      Serial  #: CH05080069
      P-ASIC  0: type 01D1, rev 00  subrev 00
      P-ASIC  1: type 01D1, rev 00  subrev 00
==========================================================================
SL 2: SX-FI42XG 2-port 10G
      Serial  #: CH05080080
      P-ASIC  2: type 01D1, rev 00  subrev 00
      P-ASIC  3: type 01D1, rev 00  subrev 00
==========================================================================
SL 9: SX-FI2XGMR4 2-port Management
      Serial  #: CH34070027
      P-ASIC 16: type 01D1, rev 00  subrev 00
      P-ASIC 17: type 01D1, rev 00  subrev 00
==========================================================================
Active Management Module:
  660 MHz Power PC processor 8541 (version 32/0020) 66 MHz bus
  512 KB boot flash memory
16384 KB code flash memory
  512 MB DRAM
The system uptime is 22 minutes 9 seconds
The system : started=cold start

FastIron SX 800 Router#sho mod
     Module                                   Status    Ports Starting MAC
 F1: SX-FISF Switch Fabric                    active
 F2: SX-FISF Switch Fabric                    active
 S1: SX-FI42XG 2-port 10G                     OK          2   0012.f226.d700
 S2: SX-FI42XG 2-port 10G                     OK          2   0012.f226.d718
 S3:
 S4:
 S5:
 S6:
 S7:
 S8:
 S9: SX-FI2XGMR4 2-port Management            Active      2   0012.f226.d7c0
     { Status : OK }
S10:                                          Standby     0
FastIron SX 800 Router#sho int e 1/1
10GigabitEthernet1/1 is down, line protocol is down
  Hardware is 10GigabitEthernet, address is 0012.f226.d700 (bia
0012.f226.d700)
  Configured speed 10Gbit, actual unknown, configured duplex fdx, actual
unknown

  Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING
  BPDU guard is Disabled, ROOT protect is Disabled
  Link Error Dampening is Disabled
  STP configured to ON, priority is level0
  Flow Control is enabled
  mirror disabled, monitor disabled
  Not member of any active trunks
  Not member of any configured trunks
  No port name
  IPG XGMII 96 bits-time
  IP MTU 1500 bytes, encapsulation ethernet
  300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
  300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
  0 packets input, 0 bytes, 0 no buffer
  Received 0 broadcasts, 0 multicasts, 0 unicasts
  0 input errors, 0 CRC, 0 frame, 0 ignored
  0 runts, 0 giants
  0 packets output, 0 bytes, 0 underruns
  Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
  0 output errors, 0 collisions
  Relay Agent Information option: Disabled
FastIron SX 800 Router#sho int e 1/2
10GigabitEthernet1/2 is down, line protocol is down
  Hardware is 10GigabitEthernet, address is 0012.f226.d701 (bia
0012.f226.d701)
  Configured speed 10Gbit, actual unknown, configured duplex fdx, actual
unknown

  Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING
  BPDU guard is Disabled, ROOT protect is Disabled
  Link Error Dampening is Disabled
  STP configured to ON, priority is level0
  Flow Control is enabled
  mirror disabled, monitor disabled
  Not member of any active trunks
  Not member of any configured trunks
  No port name
  IPG XGMII 96 bits-time
  IP MTU 1500 bytes, encapsulation ethernet
  300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
  300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
  0 packets input, 0 bytes, 0 no buffer
  Received 0 broadcasts, 0 multicasts, 0 unicasts
  0 input errors, 0 CRC, 0 frame, 0 ignored
  0 runts, 0 giants
  0 packets output, 0 bytes, 0 underruns
  Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
  0 output errors, 0 collisions
  Relay Agent Information option: Disabled
FastIron SX 800 Router#


As always, your help is greatly appreciated.

Thanks.

--Chuck
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/foundry-nsp/attachments/20090930/3d03703f/attachment.html>