[f-nsp] Port State Blocking, FastIron SX 800
Chuck Ufarley
markentime at gmail.com
Wed Sep 30 17:50:50 EDT 2009
Crisis averted. A few more reboots and this thing started to behave. Thanks
for your time, everyone.
--Chuck
On Wed, Sep 30, 2009 at 1:17 PM, Chuck Ufarley <markentime at gmail.com> wrote:
> Didn't even know there was a 5100b. Unfortunately, I tried it and got the
> same result. Port state BLOCKING. Weirder still, the management port still
> immediately goes to FORWARDING, even if nothing's connected. Anyone
> experience that?
>
> I tried downgrading to 4.2.00b, too, both SXS and SXR. Neither worked.
> Same blocking/forwarding issues. Thanks for the suggestion, though.
>
> --Chuck.
>
>
> On Wed, Sep 30, 2009 at 1:00 PM, Jared Valentine <hidden at xmission.com>wrote:
>
>> *Upgrading to 5.1.00b should fix this problem. *
>>
>> * *
>>
>> *Closed defects in IronWare R05.1.00b for the FastIron X Series Switches*
>>
>> *106289 Critical Summary*: 10 GbE ports may not link up.
>>
>> *Symptom*: No link on 10 GbE ports
>>
>> *Probability*: Medium
>>
>> *Feature*: System
>>
>> *Function*: System
>>
>>
>>
>> Jared Valentine
>>
>> hidden at xmission.com
>>
>>
>>
>>
>>
>>
>>
>> *From:* foundry-nsp-bounces at puck.nether.net [mailto:
>> foundry-nsp-bounces at puck.nether.net] *On Behalf Of *Chuck Ufarley
>> *Sent:* Wednesday, September 30, 2009 12:58 PM
>> *To:* foundry-nsp at puck.nether.net
>> *Subject:* [f-nsp] Port State Blocking, FastIron SX 800
>>
>>
>>
>> Hi all--
>>
>> I've got an FI-SX 800 with a FI-2XGMR4 PREM and a couple of FI-42XGs, and
>> I can't seem to get the ports on the 2XGs to come up. There's nothing
>> connected to the box at all. Reloads and power downs keep repeating a port
>> state BLOCKING. Can't figure out why. Console output is below. Anyone got
>> any advice?
>>
>> FastIron SX 800 Router#sho run
>> Current configuration:
>> !
>> ver 05.1.00T3e3
>> !
>> module 1 fi-sx4-2-port-10g-module
>> module 2 fi-sx4-2-port-10g-module
>> module 9 fi-sx4-2-10g-port-management-module
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> end
>>
>> FastIron SX 800 Router#sho ver
>>
>> ==========================================================================
>> Active Management CPU [Slot-9]:
>> SW: Version 05.1.00T3e3 Copyright (c) 1996-2009 Brocade Communications
>> Systems
>> , Inc.
>> Compiled on May 12 2009 at 22:13:55 labeled as SXR05100
>> (3395303 bytes) from Primary SXR05100.bin
>> BootROM: Version 05.1.00T3e5 (FEv2)
>> Serial #: SA17085232
>> HW: Chassis FastIron SX 800-PREM (PROM-TYPE SX-FIL3U)
>> ==========================================================================
>> SL 1: SX-FI42XG 2-port 10G
>> Serial #: CH05080069
>> P-ASIC 0: type 01D1, rev 00 subrev 00
>> P-ASIC 1: type 01D1, rev 00 subrev 00
>> ==========================================================================
>> SL 2: SX-FI42XG 2-port 10G
>> Serial #: CH05080080
>> P-ASIC 2: type 01D1, rev 00 subrev 00
>> P-ASIC 3: type 01D1, rev 00 subrev 00
>> ==========================================================================
>> SL 9: SX-FI2XGMR4 2-port Management
>> Serial #: CH34070027
>> P-ASIC 16: type 01D1, rev 00 subrev 00
>> P-ASIC 17: type 01D1, rev 00 subrev 00
>> ==========================================================================
>> Active Management Module:
>> 660 MHz Power PC processor 8541 (version 32/0020) 66 MHz bus
>> 512 KB boot flash memory
>> 16384 KB code flash memory
>> 512 MB DRAM
>> The system uptime is 22 minutes 9 seconds
>> The system : started=cold start
>>
>> FastIron SX 800 Router#sho mod
>> Module Status Ports Starting MAC
>> F1: SX-FISF Switch Fabric active
>> F2: SX-FISF Switch Fabric active
>> S1: SX-FI42XG 2-port 10G OK 2
>> 0012.f226.d700
>> S2: SX-FI42XG 2-port 10G OK 2
>> 0012.f226.d718
>> S3:
>> S4:
>> S5:
>> S6:
>> S7:
>> S8:
>> S9: SX-FI2XGMR4 2-port Management Active 2
>> 0012.f226.d7c0
>> { Status : OK }
>> S10: Standby 0
>> FastIron SX 800 Router#sho int e 1/1
>> 10GigabitEthernet1/1 is down, line protocol is down
>> Hardware is 10GigabitEthernet, address is 0012.f226.d700 (bia
>> 0012.f226.d700)
>> Configured speed 10Gbit, actual unknown, configured duplex fdx, actual
>> unknown
>>
>> Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING
>> BPDU guard is Disabled, ROOT protect is Disabled
>> Link Error Dampening is Disabled
>> STP configured to ON, priority is level0
>> Flow Control is enabled
>> mirror disabled, monitor disabled
>> Not member of any active trunks
>> Not member of any configured trunks
>> No port name
>> IPG XGMII 96 bits-time
>> IP MTU 1500 bytes, encapsulation ethernet
>> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>> 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>> 0 packets input, 0 bytes, 0 no buffer
>> Received 0 broadcasts, 0 multicasts, 0 unicasts
>> 0 input errors, 0 CRC, 0 frame, 0 ignored
>> 0 runts, 0 giants
>> 0 packets output, 0 bytes, 0 underruns
>> Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
>> 0 output errors, 0 collisions
>> Relay Agent Information option: Disabled
>> FastIron SX 800 Router#sho int e 1/2
>> 10GigabitEthernet1/2 is down, line protocol is down
>> Hardware is 10GigabitEthernet, address is 0012.f226.d701 (bia
>> 0012.f226.d701)
>> Configured speed 10Gbit, actual unknown, configured duplex fdx, actual
>> unknown
>>
>> Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING
>> BPDU guard is Disabled, ROOT protect is Disabled
>> Link Error Dampening is Disabled
>> STP configured to ON, priority is level0
>> Flow Control is enabled
>> mirror disabled, monitor disabled
>> Not member of any active trunks
>> Not member of any configured trunks
>> No port name
>> IPG XGMII 96 bits-time
>> IP MTU 1500 bytes, encapsulation ethernet
>> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>> 0 packets input, 0 bytes, 0 no buffer
>> Received 0 broadcasts, 0 multicasts, 0 unicasts
>> 0 input errors, 0 CRC, 0 frame, 0 ignored
>> 0 runts, 0 giants
>> 0 packets output, 0 bytes, 0 underruns
>> Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
>> 0 output errors, 0 collisions
>> Relay Agent Information option: Disabled
>> FastIron SX 800 Router#
>>
>>
>> As always, your help is greatly appreciated.
>>
>> Thanks.
>>
>> --Chuck
>>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/foundry-nsp/attachments/20090930/ae1ae6e8/attachment.html>
More information about the foundry-nsp
mailing list