[f-nsp] Disable one port within trunk group

[Jared Valentine]

Robert:

Yes, this is possible.  semi-edited output below:

FCX648SHPOE Router#
FCX648SHPOE Router#conf t
FCX648SHPOE Router(config)#int e 1/1/25 to 1/1/28
FCX648SHPOE Router(config-mif-1/1/25-1/1/28)#link-agg act
FCX648SHPOE Router(config-mif-1/1/25-1/1/28)#exit

SYSLOG: <14>0d00h03m29s:FCX648SHPOE Router Trunk: Group (1/1/25, 1/1/26,
1/1/27,
 1/1/28) created by 802.3ad link-aggregation module.

FCX648SHPOE Router#
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Interface ethernet
1/1/25, state up
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Logical link on interface
ethernet 1/1/25 is up.
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Interface ethernet
1/1/26, state up
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Logical link on interface
ethernet 1/1/26 is up.
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Interface ethernet
1/1/27, state up
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Logical link on interface
ethernet 1/1/27 is up.
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Interface ethernet
1/1/28, state up
SYSLOG: <14>0d00h03m32s:FCX648SHPOE Router System: Logical link on interface
ethernet 1/1/28 is up.

FCX648SHPOE Router(config)#
FCX648SHPOE Router(config)#trunk e 1/1/25 to 1/1/28
FCX648SHPOE Router(config-trunk-1/1/25-1/1/28)#config-trunk-ind
FCX648SHPOE Router(config-trunk-1/1/25-1/1/28)#dis e 1/1/25

SYSLOG: <14>0d00h03m42s:FCX648SHPOE Router System: Interface ethernet
1/1/25, state down

FCX648SHPOE Router(config-trunk-1/1/25-1/1/28)#show trunk

Configured trunks:

Trunk ID: 25
Hw Trunk ID: 1
Ports_Configured: 4
Primary Port Monitored: Individually

Ports         1/1/25  1/1/26  1/1/27  1/1/28
Port Names    none    none    none    none
Port_Status   disable enable  enable  enable
Monitor       off     off     off     off
Rx Mirr Port  N/A     N/A     N/A     N/A
Tx Mirr Port  N/A     N/A     N/A     N/A
Monitor Dir   N/A     N/A     N/A     N/A

Operational trunks:

Trunk ID: 25
Hw Trunk ID: 1
Duplex: Full
Speed: 1G
Tag: No
Priority: level0
Active Ports: 3

Ports         1/1/25  1/1/26  1/1/27  1/1/28
Link_Status   down    active  active  active
port_state    Disable Forward Forward Forward
LACP_Status   down    ready   ready   ready

FCX648SHPOE Router(config-trunk-1/1/25-1/1/28)#


-----Original Message-----
From: foundry-nsp-bounces at puck.nether.net
[mailto:foundry-nsp-bounces at puck.nether.net] On Behalf Of Robert Hass
Sent: Monday, June 06, 2011 3:46 AM
To: foundry-nsp at puck.nether.net
Subject: [f-nsp] Disable one port within trunk group

Hi

I would like to disable 1 GE port which is assigned to trunk group
(LAG currently consist 4 GE ports) but software reject entering into
interface level:

telnet at lab-fcx(config)#int e1/1/5
Error - cannot configure secondary ports of a trunk

Can I do this some way ?

My configuration:

interface ethernet 1/1/3
 port-name GE to TEST-6500
 load-interval 30
 spanning-tree 802-1w admin-pt2pt-mac
 no flow-control
 link-aggregate configure key 40000
 link-aggregate active
 pvst-mode
!
interface ethernet 1/1/4
 port-name GE to TEST-6500
 link-aggregate configure key 40000
 link-aggregate active
 pvst-mode
!
interface ethernet 1/1/5
 port-name GE to TEST-6500
 link-aggregate configure key 40000
 link-aggregate active
 pvst-mode
!
interface ethernet 1/1/6
 port-name GE to TEST-6500
 link-aggregate configure key 40000
 link-aggregate active
 pvst-mode
!

telnet at lab-fcx#sh ver
  Copyright (c) 1996-2010 Brocade Communications Systems, Inc.
    UNIT 1: compiled on Sep 20 2010 at 22:46:47 labeled as FCXR07200
                (5591177 bytes) from Secondary FCXR07200.bin
        SW: Version 07.2.00T7f3
  Boot-Monitor Image size = 369292, Version:07.1.00T7f5 (grz07100)
  HW: Stackable FCX624

Robert
_______________________________________________
foundry-nsp mailing list
foundry-nsp at puck.nether.net
http://puck.nether.net/mailman/listinfo/foundry-nsp