DX-60 Repair Adventure, or DX-60 only Works on its Side

[Brian Carling]

Hey that;'s great Scott - I have the same set up here and am 
similarly working my way through all of it.

Got the externaol relay to jhook up yet,
and the HR10B should also be working fine.

See you on the air some time with the same set up!

73 - Bry, AF4K

> Over the past several of years I've casually collected an HR-10B, HG-10,
> DX-60B but I haven't gotten around to assembling the station yet.  
> 
> Friday I got the bug to get the Heath station up and running so I moved it
> down off the shelf and into the one of the operating positions.
> 
> Last year I realigned the HR-10B receiver, so I didn't have
> to do anything with it other than wire up the mute contacts to the
> antenna relay. I was listening to 40 meter CW while I was
> working on the transmitter.  That HR-10B sounds pretty nice and was probably
> a nice beginning ham receiver.  It sounds alot better than some of the junk
> that was sold as a 'ham receiver'.  The Conar 500 comes to mind, or the
> Ameco R5.
> 
> I hooked up the VFO and TX and just fired it up.  There was very little
> grid current and the frequency wobbled with out any provocation, so I put
> the TX on the bench and opened it up, set it upside down. I checked the voltages and they were 
> good (at where I was measuring them... hint hint).  Then checked the tubes and the 
> 6146 was bad so I replaced it.  I was now getting grid current.... ok.... that was
> easy.  I had a crystal in and I listened to the signal on the receiver.  The oscillator was
> stable and sounding very
> good.  I turned it over, closed up the PA cage, and went to measure power but got nothing.
> No grid current again.  Huh?
> 
> So I set it on its side to start probing and got grid current right away. 
> I started tapping around the chassis and found it was intermittant.  It seemed to be the worst
> when I tapped on the PI Network box, so I shut it down and pulled the box off the chassis.
> I found a burned up silver mica on the last stage, but that wouldn't account for the
> intermittent problem.  I replaced the silver mica and then touched up all the solder
> joints in the box, reattached it, powered up the DX-60, and it was still intermittent. By the
> way, those PI filter box screws such are a bugger to get at.... 
> 
> I was now tapping under the chassis with the Red Heathkit plastic nut driver, tapping components, 
> sections, and I found an unsoldered joint.  AH HA.  Soldered it, turned it back on, and... and...it
> was still intermittent.  
> 
> By now I'm starting to notice that it often works on its side but it never
> works when its sitting down on the table...  Up/down, Up/down, work/no work :))) With the TX on its side,
> I continued tapping but I couldn't find a sensitive area.  I got down on the
> floor so I could peer up under the chassis as I lowered it down to the table, and I saw a brief ZZZtttt.
> It was in the high voltage section, a lug had a couple of HV connections on it, and one of them
> was not soldered.  It was hidden under the soldered joint above it. So what apparently was 
> happening was the connection was made when the TX was laying 
> on its side or upside down, but when the TX was placed flat on its feet, the weight of the power 
> transformer tweaked that
> joint slightly, opening the connection... Sheesh.... So I 
> soldered it up and that was the end of
> the intermittent problem.  After than I went through and looked at the rest of the connections,
> hunting for any more unsoldered joints.   I should have recapped the high voltage electrolytics
> but I didn't have the right value so I'll order them from Mouser.  I also retighted every screw and
> nut in there, relubed up the rotary switches, a little DeOxit here and there.
> 
> I just started going through the HG-10 VFO before calling it a day.  Maybe I'll get to that this 
> week and have the classic Heathkit station on the air by the weekend.  I love CW and hope to have
> a ball with this station on CW.  While I hear an occasional DX-60 on AM, I'm not
> that much of a masochist  :)
> 
> I thought you guys would get a kick out the sideways adventure.
> 
> Did Heathkit ever give away blank QSL cards for Novices to use?
> 
> Last night I closed up the HG-10 VFO, hooked it all up, and tested it.  The TX/VFO signal sounds
> great, stable, clean.  I called CQ a few times on 40 with no response and called it a night.
> 
> 73, Scott WA9WFA
> 
> -----------------------------------------------------------
> Products bought, sold or traded here is the responsibility of the
> parties involved.  This list and the City of Tempe are not responsible
> for losses or misrepresentations of any kind.  Buyer beware!
> 
> -----------------------------------------------------------
> This list is a public service of the City of Tempe, Arizona
> -----------------------------------------------------------
> 
> Subscription control - http://www.tempe.gov/lists/control.asp?list=HEATH
> To post - HEATH at LISTSERV.TEMPE.GOV
> Archives - http://listserv.tempe.gov/archives/HEATH.html
> 

-----------------------------------------------------------
Products bought, sold or traded here is the responsibility of the
parties involved.  This list and the City of Tempe are not responsible
for losses or misrepresentations of any kind.  Buyer beware!

-----------------------------------------------------------
This list is a public service of the City of Tempe, Arizona
-----------------------------------------------------------

Subscription control - http://www.tempe.gov/lists/control.asp?list=HEATH
To post - HEATH at LISTSERV.TEMPE.GOV
Archives - http://listserv.tempe.gov/archives/HEATH.html