[j-nsp] JunOS upgrade to 8.5R1.14, boot device too small ?

[Shawn Morris]

I should add that you should 'req sys snapshot' before installing the
card so that it will boot properly from the HD afterwards.  Then you
should run 'req sys snapshot partition' to correctly partition and
restore the CF after installation.

On 12/25/07, Shawn Morris <shawn at smorris.com> wrote:
> There is a card, but it is located underneath the daughter board that
> hold the hard drive.  I do not believe there is an officially
> supported method for upgrading the CF on RE2.  However in our lab we
> have had success replacing them with standard Sandisk 1gb CF cards.
> That involves removing a number of screws from the bottom and removing
> the face plate.  Then you must remove the daughterboard containing the
> HD and there is another daughterboard underneath that holds the CF
> card.
>
> On 12/25/07, Mykola Mitrokhin <mkmrtkhn at gmail.com> wrote:
> > hello David,
> >
> > Thank you for your quick reply. I have read the requirement. But i use a
> > RE-2.0 333 768 routing engine in this system,
> > 'without' a flash card. There is no card onboard or in the back. Is there no
> > option to resize partitions or something?
> >
> > Thank you for your great help.
> >
> > best regards,
> > mykola
> >
> >
> > 2007/12/25, David Ball <davidtball at gmail.com>:
> > >
> > > Hi Mykola.  Check out the release notes for JunOS 8.5.
> > >
> > > http://www.juniper.net/techpubs/software/junos/junos85/rn-sw-85/release-8.5-features.html#rn-new-features
> > >
> > > In the section that discusses FreeBSD they make mention to the
> > > requirement of a 256MB or larger Compact Flash card (part of your RE)
> > > in order to install 8.5.  Sounds as though yours doesn't meet this
> > > criteria.  The cheap way to get around this is to stick with older
> > > code, the more expensive way is to upgrade your compact flash.  There
> > > have been some discussions about this in the last week or 2 on the
> > > list, so perhaps peruse the archives as well for others' experiences.
> > >
> > > David
> > >
> > >
> > > On 25/12/2007, Mykola Mitrokhin <mkmrtkhn at gmail.com> wrote:
> > > > Hello,
> > > >
> > > > I have a problem with upgrading one of our juniper routers, currently it
> > > is
> > > > running JunOS 8.3.
> > > > I wanted to upgrade to -8.5R1.14
> > > >
> > > > I started the upgrade and it ends with the following error:
> > > >
> > > > *********************
> > > >
> > > > Adding jinstall...
> > > >
> > > > WARNING: This installation will not succeed.
> > > > WARNING: The boot device is less than 256M.
> > > > WARNING: A hardware upgrade is required.
> > > >
> > > > ERROR: jinstall fails requirements check
> > > >
> > > > **********************
> > > >
> > > > How can i fix this? I use RE-2.0 333-768
> > > >
> > > >
> > > >
> > > > Thanks for your help in advance.
> > > >
> > > >
> > > >
> > > > Best wishes,
> > > >
> > > > mykola
> > > > _______________________________________________
> > > > juniper-nsp mailing list juniper-nsp at puck.nether.net
> > > > https://puck.nether.net/mailman/listinfo/juniper-nsp
> > > >
> > >
> > _______________________________________________
> > juniper-nsp mailing list juniper-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/juniper-nsp
> >
>
>
> --
> Shawn Morris
> IP Development - NTT America
> shawn at smorris.com/shawn at ntt.net/shawn at us.ntt.net
> v: +1 214 915 1361 f: +1 815 327 3016
>


-- 
Shawn Morris
IP Development - NTT America
shawn at smorris.com/shawn at ntt.net/shawn at us.ntt.net
v: +1 214 915 1361 f: +1 815 327 3016