[j-nsp] juniper-nsp Digest, Vol 81, Issue 22

[emhell at gmail.com]

I did 3 x just vm
Sent from my BlackBerry® smartphone with Nextel Direct Connect

-----Original Message-----
From: juniper-nsp-request at puck.nether.net

Date: Fri, 14 Aug 2009 12:00:02 
To: <juniper-nsp at puck.nether.net>
Subject: juniper-nsp Digest, Vol 81, Issue 22


Send juniper-nsp mailing list submissions to
	juniper-nsp at puck.nether.net

To subscribe or unsubscribe via the World Wide Web, visit
	https://puck.nether.net/mailman/listinfo/juniper-nsp
or, via email, send a message with subject or body 'help' to
	juniper-nsp-request at puck.nether.net

You can reach the person managing the list at
	juniper-nsp-owner at puck.nether.net

When replying, please edit your Subject line so it is more specific
than "Re: Contents of juniper-nsp digest..."


Today's Topics:

   1. Re: AS-path (Judah Scott)
   2. Re: M7i Hard Disk Replacement (Kevin Loch)


----------------------------------------------------------------------

Message: 1
Date: Thu, 13 Aug 2009 10:17:57 -0700
From: Judah Scott <judah.scott.iam at gmail.com>
To: Paul Goyette <pgoyette at juniper.net>
Cc: "juniper-nsp at puck.nether.net" <juniper-nsp at puck.nether.net>
Subject: Re: [j-nsp] AS-path
Message-ID:
	<3172b9cb0908131017o20a4af9ai8335d2a79843bccf at mail.gmail.com>
Content-Type: text/plain; charset=ISO-8859-1

I think the most important note on regexp in as-path is that the basic
matching unit is the AS number and not individual characters.  For AS-Path,
the guide notes the ! as not operator and no mention of the [^] which is the
negated character set, or "except" operator, as Paul mentioned.

However, according to the guide the community strings are matched on a
per-character basis and they do note the [] and use of [^] operators.  The
whole thing is a little confusing given the two regexp engines.  Below are
the links where I found this info.


AS-Path:
http://www.juniper.net/techpubs/en_US/junos9.5/information-products/topic-collections/config-guide-policy/policy-configuring-as-path-regular-expressions-to-use-as-routing-policy-match-conditions.html#id-10278439

Community Strings:
http://www.juniper.net/techpubs/en_US/junos9.5/information-products/topic-collections/config-guide-policy/policy-defining-bgp-communities-and-extended-communities-for-use-in-routing-policy-match-conditions.html#id-10247318


Thanks,
J Scott


On Thu, Aug 13, 2009 at 5:25 AM, Paul Goyette <pgoyette at juniper.net> wrote:

> IIRC, the standard RegExp "except" operator IS supported:
>
> > set as-path 100not1000orig ".* 100 .* (!1000)$"
>
> set as-path 100not1000orig ".* 100 .* [^1000]$"
>


------------------------------

Message: 2
Date: Thu, 13 Aug 2009 13:20:46 -0400
From: Kevin Loch <kloch at kl.net>
To: juniper-nsp at puck.nether.net
Subject: Re: [j-nsp] M7i Hard Disk Replacement
Message-ID: <4A844B6E.90701 at kl.net>
Content-Type: text/plain; charset=ISO-8859-1; format=flowed

Kevin Oberman wrote:
>> Date: Wed, 12 Aug 2009 12:19:41 -0400
>> From: Brendan Mannella <bmannella at teraswitch.com>
>> Sender: juniper-nsp-bounces at puck.nether.net
>>
>> Hello,
>>
>> I was wondering if anyone has successfully replaced a hard disk on a M7i
>> RE-5.0. If so with what model disk, and once installed what is the procedure
>> to get the disk back to working/formatted condition.
> 
> No magic involved. Just replace it with a disk of the same or greater
> capacity. Be sure it's one rated for continuous operation, not a
> standard laptop drive. (This will make the drive a lot more expensive!)
> 
> 
> Then just "request system snapshot partition" for format, partition, load
> the drive.

Make sure the jumper on the drive is set to "slave" mode.

- Kevin


------------------------------

_______________________________________________
juniper-nsp mailing list
juniper-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp

End of juniper-nsp Digest, Vol 81, Issue 22
*******************************************