[j-nsp] Diagnostic Optics MIB support

Bjørn Tore bt at paulen.net
Wed Feb 24 08:18:09 EST 2010


Alessandro Inzerilli skrev:
> Hello,
>
> I'm looking for JunOS MIBs giving access to diagnostic optics 
> information, basically what you see issuing the CLI command
>
> show interfaces diagnostics optics
> Physical interface: so-0/0/0
>    Laser bias current                        :  21.392 mA
>    Laser output power                        :  0.2970 mW / -5.27 dBm
>    Module temperature                        :  46 degrees C / 115 
> degrees F
>    Module voltage                            :  3.2020 V
>    Receiver signal average optical power     :  0.0195 mW / -17.10 dBm
>    Laser bias current high alarm             :  Off
>    Laser bias current low alarm              :  Off
>    Laser bias current high warning           :  Off
>    Laser bias current low warning            :  Off
>    Laser output power high alarm             :  Off
>    Laser output power low alarm              :  Off
>    Laser output power high warning           :  Off
>    Laser output power low warning            :  Off
>    Module temperature high alarm             :  Off
>    Module temperature low alarm              :  Off
>    Module temperature high warning           :  Off
>    Module temperature low warning            :  Off
>    Module voltage high alarm                 :  Off
>    Module voltage low alarm                  :  Off
>    Module voltage high warning               :  Off
>    Module voltage low warning                :  Off
>    Laser rx power high alarm                 :  Off
>    Laser rx power low alarm                  :  Off
>    Laser rx power high warning               :  Off
>    Laser rx power low warning                :  Off
>    Laser bias current high alarm threshold   :  80.000 mA
>    Laser bias current low alarm threshold    :  2.000 mA
>    Laser bias current high warning threshold :  70.000 mA
>    Laser bias current low warning threshold  :  4.000 mA
>    Laser output power high alarm threshold   :  1.2590 mW / 1.00 dBm
>    Laser output power low alarm threshold    :  0.0440 mW / -13.57 dBm
>    Laser output power high warning threshold :  0.7940 mW / -1.00 dBm
>    Laser output power low warning threshold  :  0.0700 mW / -11.55 dBm
>    Module temperature high alarm threshold   :  110 degrees C / 230 
> degrees F
>    Module temperature low alarm threshold    :  -40 degrees C / -40 
> degrees F
>    Module temperature high warning threshold :  93 degrees C / 199 
> degrees F
>    Module temperature low warning threshold  :  -30 degrees C / -22 
> degrees F
>    Module voltage high alarm threshold       :  3.900 V
>    Module voltage low alarm threshold        :  2.700 V
>    Module voltage high warning threshold     :  3.700 V
>    Module voltage low warning threshold      :  2.900 V
>    Laser rx power high alarm threshold       :  1.1748 mW / 0.70 dBm
>    Laser rx power low alarm threshold        :  0.0039 mW / -24.09 dBm
>    Laser rx power high warning threshold     :  0.7942 mW / -1.00 dBm
>    Laser rx power low warning threshold      :  0.0100 mW / -20.00 dBm
>
>
> Does anybody know if the MIBs exist? I couldn't find anything on 
> juniper tech docs.
>
> Thanks,
> Alessandro

Maybe this could point you in the correct direction?
http://forums.cacti.net/about23089.html

-- 
Bjørn Tore Paulen




More information about the juniper-nsp mailing list