[j-nsp] MPLS L2VPN Cisco and Juniper

[Aaron]

Thanks Alex, does it work on vMX ?

Aaron

-----Original Message-----
From: juniper-nsp [mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of
Alexander Arseniev
Sent: Monday, April 18, 2016 11:26 AM
To: juniper-nsp at puck.nether.net
Subject: Re: [j-nsp] MPLS L2VPN Cisco and Juniper

Hello,
If You are doing the below JUNOS config on Olive, L2circuit data plane does
not work on Olive.
And it never worked on Olive, to my knowledge.
HTH
Thx
Alex

On 18/04/2016 13:32, Mohammad Khalil wrote:
> I have configured the below
> set interfaces em0 mtu 1514
> set interfaces em0 unit 0 family inet address 192.168.101.10/24 set 
> interfaces em0 unit 0 family mpls mtu 1500 set interfaces em1 
> vlan-tagging set interfaces em1 unit 100 encapsulation vlan-ccc set 
> interfaces em1 unit 100 vlan-id 100 set interfaces em1 unit 100 family 
> ccc set interfaces lo0 unit 0 family inet address 10.10.10.10/32 set 
> routing-options router-id 10.10.10.10 set routing-options 
> autonomous-system 20 set protocols mpls interface em0.0 set protocols 
> mpls interface lo0.0 set protocols ospf area 0.0.0.0 interface em0.0 
> set protocols ospf area 0.0.0.0 interface lo0.0 set protocols ldp 
> interface em0.0 set protocols ldp interface lo0.0 set protocols 
> l2circuit neighbor 1.1.1.1 interface em1.100 virtual-circuit-id 100
>
> router ospf 1
>   router-id 1.1.1.1
>   network 1.1.1.1 0.0.0.0 area 0
>   network 192.168.101.1 0.0.0.0 area 0 R1#sh run int f1/1.100 Building 
> configuration...
>
> Current configuration : 107 bytes
> !
> interface FastEthernet1/1.100
>   encapsulation dot1Q 100
>   xconnect 10.10.10.10 100 encapsulation mpls end
>
> But its not working even the circuit is up (not working means no ping 
> between CEs)
>
> BR,
> Mohammad
>
> On Mon, Apr 18, 2016 at 2:47 PM, Mohammad Khalil <eng.mssk at gmail.com>
wrote:
>
>> Thanks Steinar
>> So we are talking about xconnect from Cisco side and l2circuit from 
>> Juniper side right?
>> Do you have a running template please?
>>
>> Thanks in advance
>>
>> BR,
>> Mohammad
>>
>> On Mon, Apr 18, 2016 at 1:49 PM, <sthaug at nethelp.no> wrote:
>>
>>>> Am trying to configure MPLS L2VPN between Cisco and Juniper I know 
>>>> in Cisco VPLS and xconnect In juniper l2vpn and l2circuit (Kompella 
>>>> and Martini respectively) What are the compatible methods to follow 
>>>> in this case?
>>> Point to point (pseudowire, Martini tunnel) is very much 
>>> interoperable between Cisco and Juniper. We have lots of these in
operation.
>>>
>>> Steinar Haug, Nethelp consulting, sthaug at nethelp.no
>>>
>>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net 
> https://puck.nether.net/mailman/listinfo/juniper-nsp

_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp