[j-nsp] Throughput testing tools on Juniper?

[Giuliano Medalha]

But for MX240, MX480 and MX960 you will need to combine SCB, MPC and MIC to
test the chassis ...

There is a lot of combinations and possibilities ... SCBE, SCBE2, MPC1,
MPC2, MPC3, MPC4, MPC5, NG-MPC-2 and NG-MPC-3. A lot of MIC types ... gig,
10gig, 40gig and 100gig ...

Are you going to test performance Gbps and PPS ?  Using TCP and UDP ?
Mixed mode and 64 bytes ?

Att,

Giuliano

Giuliano Cardozo Medalha
Systems Engineer
+55 (17) 3011-3811
+55 (17) 98112-5394
JUNIPER J-PARTNER ELITE
giuliano at wztech.com.br
http://www.wztech.com.br/



​
WZTECH is registered trademark of WZTECH NETWORKS.
Copyright © 2015 WZTECH NETWORKS. All Rights Reserved.

IMPORTANTE:
As informações deste e-mail e o conteúdo dos  eventuais  documentos anexos
são confidenciais e para conhecimento exclusivo do destinatário. Se o
leitor  desta  mensagem  não  for o seu destinatário,
fica desde já notificado de que não poderá  divulgar,  distribuir ou, sob
qualquer forma, dar conhecimento a terceiros das informações e do conteúdo
dos documentos anexos. Neste caso, favor comunicar imediatamente
o remetente, respondendo este e-mail ou telefonando ao mesmo, e em seguida
apague-o.


CONFIDENTIALITY NOTICE:
The information transmitted in this email message and any attachments are
solely for the intended recipient and may contain confidential or
privileged information. If you are not the intended recipient, any review,
transmission,  dissemination or other use of this information is
prohibited. If you have received this communication in error, please notify
the sender immediately and delete the material from any computer, including
any copies.

On Sun, Feb 7, 2016 at 9:11 PM, Shanawaz <shanawaz at gmail.com> wrote:

> Hi Tomasz,
>
> We are looking to run the test on a few different MX platforms (5, 80, 240,
> 480, 960)
>
>
>
> On Thu, Feb 4, 2016 at 6:43 PM, Tomasz Mikołajek <tmikolajek at gmail.com>
> wrote:
>
> > Hi.
> > You can configure rfc 2544 test. What Juniper device you have?
> >
> >
> > W dniu czwartek, 4 lutego 2016 Shanawaz <shanawaz at gmail.com> napisał(a):
> >
> >> Hey Folks,
> >>
> >> Are there any tools similar to iperf (or ttcp on cisco) that we can run
> >> between 2 Juniper routers (from the CLI or the shell) to test throughput
> >> between the 2 devices?
> >>
> >> We are suspecting a hard rate-limit placed in an upstream ISP segment
> >> between the 2 devices. It would be nice just to test between the routers
> >> at
> >> both ends of the ISP segment rather than using machines that are a few
> >> more
> >> subnets away.
> >>
> >> Thanks,
> >> Shan
> >> _______________________________________________
> >> juniper-nsp mailing list juniper-nsp at puck.nether.net
> >> https://puck.nether.net/mailman/listinfo/juniper-nsp
> >>
> >
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp