[j-nsp] ACX50xx l2circuit counters

[Giuliano Medalha]

Hum ... I think in ACX you will need to explicit use statistics command ...


set interfaces xe-0/0/1 statistics



Giuliano Cardozo Medalha
Systems Engineer
+55 (17) 3011-3811
+55 (17) 98112-5394
JUNIPER J-PARTNER ELITE
giuliano at wztech.com.br
http://www.wztech.com.br/



​
WZTECH is registered trademark of WZTECH NETWORKS.
Copyright © 2016 WZTECH NETWORKS. All Rights Reserved.

IMPORTANTE:
As informações deste e-mail e o conteúdo dos  eventuais  documentos anexos
são confidenciais e para conhecimento exclusivo do destinatário. Se o
leitor  desta  mensagem  não  for o seu destinatário,
fica desde já notificado de que não poderá  divulgar,  distribuir ou, sob
qualquer forma, dar conhecimento a terceiros das informações e do conteúdo
dos documentos anexos. Neste caso, favor comunicar imediatamente
o remetente, respondendo este e-mail ou telefonando ao mesmo, e em seguida
apague-o.


CONFIDENTIALITY NOTICE:
The information transmitted in this email message and any attachments are
solely for the intended recipient and may contain confidential or
privileged information. If you are not the intended recipient, any review,
transmission,  dissemination or other use of this information is
prohibited. If you have received this communication in error, please notify
the sender immediately and delete the material from any computer, including
any copies.

On Mon, Jun 20, 2016 at 6:37 PM, Aaron <aaron1 at gvtc.com> wrote:

> Yeah, strange my subinterface doesn't show any packets out, but the phy
> int shows currently 17 mbps going out right now...
>
> Maybe these counters are broken on the subint... I tried walking with snmp
> but I still didn't see any traffic for the subinterface used on the
> l2circuit
>
> agould at blcn-h-5048> show interfaces ge-0/0/12 statistics
> Physical interface: ge-0/0/12, Enabled, Physical link is Up
>   Interface index: 650, SNMP ifIndex: 521
>   Link-level type: Ethernet-CCC, MTU: 1514, LAN-PHY mode, Speed: 1000mbps,
> BPDU Error: None, MAC-REWRITE Error: None, Loopback: Disabled,
>   Source filtering: Disabled, Flow control: Disabled, Auto-negotiation:
> Enabled, Remote fault: Online, Media type: Copper
>   Device flags   : Present Running
>   Interface flags: SNMP-Traps Internal: 0x4000
>   Link flags     : None
>   CoS queues     : 8 supported, 8 maximum usable queues
>   Current address: 20:4e:71:45:12:34, Hardware address: 20:4e:71:45:12:34
>   Last flapped   : 2016-05-25 14:38:24 CDT (3w5d 01:55 ago)
>   Statistics last cleared: Never
>   Input rate     : 17802616 bps (1633 pps)
>   Output rate    : 0 bps (0 pps)
>   Input errors: 0, Output errors: 0
>   Active alarms  : None
>   Active defects : None
>   Interface transmit statistics: Disabled
>
>   Logical interface ge-0/0/12.0 (Index 557) (SNMP ifIndex 523)
>     Flags: Up SNMP-Traps 0x4004000 Encapsulation: Ethernet-CCC
>     Input packets : 68
>     Output packets: 0
>     Protocol ccc, MTU: 1514
>       Flags: Is-Primary
>
> {master:0}
>
> agould at blcn-h-5048> show l2circuit connections brief
> Layer-2 Circuit Connections:
>
> Legend for connection status (St)
> ....
>
> Legend for interface status
> Up -- operational
> Dn -- down
> Neighbor: 10.101.0.1
>     Interface                 Type  St     Time last up          # Up trans
>     ge-0/0/12.0(vc 1)         rmt   Up     May 25 14:38:24 2016           1
>
>
> - Aaron
>
>
>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp
>