[cisco-voip] 2801 MGCP Gateway on CCM 5.0

[omar parihuana]

Hi,

Maybe you can disble ip domain name and use only IP address in CCM and
Gateway,

with sh ccm you must see the registration.

Rgds.


On 3/2/07, Jonathan Charles <jonvoip at gmail.com> wrote:
>
> In CCM, you need to setup the gateway name as:
>
> GW2801.test.br
>
> This is your hostname and your ip domain name...
>
> There is no other method.
>
> When you say it is 'active' on the gateway, that doesn't correspond to
> what it should say...
>
> If you do a:
>
> show ccm
>
> you should see it say primary and registered.
>
> And then on CCM, click on show endpoints and you should see a 'registered
> with...' if it is up.
>
>
> Jonathan
>
>
> On 2/28/07, alsvrj <alsvrj at superig.com.br> wrote:
>
> > Hello All,
> >
> > I have an 2801 connected to a Hicom 330 PBX through a ISDN PRI QSIG with
> > MGCP and a CCM5.0 . I´m having a lot of problems to get the gateway
> > registration on CCM.
> >
> > I would like to do some questions:
> > 1- Is it possible to put an ISDN PRI with MGCP using QSIG signaling ?
> >
> > Using the show isdn status command I´m seeing
> > MULTIPLE_FRAME_ESTABILISHED
> >
> > I´m seeing too with the show ccm-manager that the MGCP is Active but I´m
> > not
> > able to see this Gateway into the active state inside of CCM.
> >
> > I´m using a VWIC-1MFT-E1 card to use this ISDN PRI.
> >
> > 2- Is it possible to put the IP Address instead of Domain Name when I´m
> > creating the 2801 Gateway ?
> >
> > Hey guys, I really need your help to solve this registration problem, I
> > kindly ask a hand into this situation.
> >
> > Thanks for everything.
> >
> > It follows below the configuration on the Gateway:
> >
> > hostname GW2801
> > !
> > boot-start-marker
> > boot system flash c2801-adventerprisek9-mz.124-6.T3.bin
> > boot-end-marker
> > !
> > logging buffered 4096 informational
> > enable secret 5 ********************
> > !
> > no aaa new-model
> > !
> > resource policy
> > !
> > clock timezone UTC -3
> > network-clock-participate wic 2
> > network-clock-select 1 E1 0/2/0
> > ip cef
> > !
> > !
> > !
> > !
> > ip tcp synwait-time 13
> > no ip domain lookup
> > ip domain name test.br
> > ip name-server *.*.*.*
> > ip name-server *.*.*.*
> > ip name-server *.*.*.*
> > !
> > isdn switch-type primary-qsig
> > isdn logging
> > !
> > voice-card 0
> > dsp services dspfarm
> > !
> > !
> > voice call carrier capacity active
> > !
> > !
> > voice class codec 1
> > codec preference 1 g711ulaw
> > codec preference 2 g729r8 bytes 40
> > !
> > !
> > !
> > voice class h323 1
> > h225 timeout tcp establish 3
> > !
> > crypto configuration
> > !
> > controller E1 0/2/0
> > framing NO-CRC4
> > line-termination 75-ohm
> > pri-group timeslots 1-31 service mgcp
> > !
> > !
> > interface FastEthernet0/0
> > ip address *.*.*.* *.*.*.*
> > speed 100
> > full-duplex
> > no cdp enable
> > h323-gateway voip bind srcaddr *.*.*.*
> > !
> > interface FastEthernet0/1
> > no ip address
> > shutdown
> > duplex auto
> > speed auto
> > no cdp enable
> > !
> > interface Serial0/1/0
> > no ip address
> > shutdown
> > clock rate 2000000
> > no cdp enable
> > !
> > interface Serial0/2/0:15
> > no ip address
> > no ip proxy-arp
> > encapsulation hdlc
> > isdn switch-type primary-qsig
> > isdn overlap-receiving
> > isdn incoming-voice voice
> > isdn supp-service name calling
> > isdn bind-l3 ccm-manager
> > isdn negotiate-bchan
> > isdn bchan-number-order ascending
> > isdn sending-complete
> > no cdp enable
> > !
> > ip route 0.0.0.0 0.0.0.0 *.*.*.*
> > !
> > !
> > ip http server
> > ip http secure-server
> > !
> > logging *.*.*.*
> > access-list 1 permit *.*.*.*
> > access-list 1 permit *.*.*.*
> > dialer-list 1 protocol ip permit
> > snmp-server community voip RW 1
> > snmp-server community ext0399 RW 1
> > snmp-server community sw0399 RW 1
> > disable-eadi
> > no cdp run
> > !
> > control-plane
> > !
> > voice-port 0/2/0:15
> > !
> > ccm-manager mgcp
> > ccm-manager music-on-hold
> > ccm-manager config server *.*.*.*
> > ccm-manager config
> > !
> > mgcp
> > mgcp call-agent *.*.*.* 2427 service-type mgcp version 0.1
> > mgcp dtmf-relay voip codec all mode out-of-band
> > mgcp rtp unreachable timeout 1000 action notify
> > mgcp modem passthrough voip mode nse
> > mgcp package-capability rtp-package
> > no mgcp package-capability res-package
> > mgcp package-capability sst-package
> > no mgcp package-capability fxr-package
> > mgcp package-capability pre-package
> > no mgcp timer receive-rtcp
> > mgcp sdp simple
> > mgcp fax t38 inhibit
> > mgcp rtp payload-type g726r16 static
> > !
> > mgcp profile default
> > !
> > !
> > dial-peer cor custom
> > !
> > !
> > !
> > dial-peer voice 1 pots
> > service mgcpapp
> > port 0/2/0:15
> > !
> > !
> > !
> > line con 0
> > exec-timeout 0 0
> > password 7 *****************
> > logging synchronous
> > login
> > line aux 0
> > exec-timeout 0 0
> > password 7 *****************
> > logging synchronous
> > login
> > line vty 0 4
> > exec-timeout 0 0
> > password 7 **************
> > logging synchronous
> > login
> > !
> > scheduler allocate 20000 1000
> > ntp clock-period 17180079
> > ntp server *.*.*.*
> > !
> > webvpn context Default_context
> > ssl authenticate verify all
> > !
> > no inservice
> > end
> >
> >
> >
> >
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> >
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>


-- 
Omar E.P.T
-----------------
Certified Networking Professionals make better Connections!

http://omarept.blogspot.com/

  Usysnet Corp
Open Source Solutions
www.usysnet.com.pe
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20070302/be0212e1/attachment.html