[cisco-voip] Supervisory Disconnect on ATA 190

[Brian Meade]

It looks like you need one of the audio input modules for that controller-
http://www.logison.com/components/paging-and-music-components.html

You'll want the telephone one.

As Mike said, supervisor disconnect is only something you need to worry
about when it won't cut off the page after completed.

On Fri, Jul 22, 2016 at 2:32 PM, Cannizzaro, Vince <
Vince.Cannizzaro at hamilton.ca> wrote:

> Hey Brian,
>
>
>
> Thanks for your reply.  The vendor connected the analog line to Analog
> input 3.  I plugged an analog phone into the other end but don’t get dial
> tone.
>
> I attached a picture to give an idea.
>
>
>
> I don’t see where I can configure supervisor disconnect on the ATA port,
> may need an FXO as you mentioned.  We’re likely looking at getting a Bogen
> UTI 1 interface which has the disconnect built in as per the vendor’s
> recommendations if we can’t use the ATA. I just wanted to make sure I
> wasn’t missing anything with the ATA before we get additional equipment
> installed.
>
>
>
> Kind regards,
>
> Vince
>
>
>
> *From:* bmeade90 at gmail.com [mailto:bmeade90 at gmail.com] *On Behalf Of *Brian
> Meade
> *Sent:* July-22-16 2:21 PM
> *To:* Cannizzaro, Vince
> *Cc:* cisco-voip at puck.nether.net
> *Subject:* Re: [cisco-voip] Supervisory Disconnect on ATA 190
>
>
>
> Which input on the Logison NCP are you hooked up to?  It sounds like maybe
> the microphone or AUX input rather than the telephone input as it shouldn't
> play anything through the speakers until it detects ringing voltage and
> then goes off-hook.  It may be that this thing needs an FXO port instead.
> Have you tried hooking up a buttset to the paging controller and seeing if
> you get dial-tone from it?
>
>
>
> On Fri, Jul 22, 2016 at 1:37 PM, Cannizzaro, Vince <
> Vince.Cannizzaro at hamilton.ca> wrote:
>
> Hi everyone,
>
>
>
> I’m trying to connect an ATA 190 to a Logison Paging Module a vendor
> installed to get paging functionality at a site.  The vendor has stated the
> following:
>
>
>
> “Upon dialing the specific  extension assigned to paging,  this line is
> “live” (i.e. answers the line A.K.A. Auto Answer) to complete the
> connection to the Logison NCP and enables the page to be broadcast on all
> the Logison Speakers you have assigned to that specific paging zone.  The
> line must also be programmed with Supervisor Disconnect (this ensures that
> the page is disconnected once the user has stopped talking and hangs up).”
>
>
>
> As it stands, as soon as I plug in the analog line into the ATA you can
> hear dial tone over the speakers and then eventually times out.
>
> I can’t see where to configure supervisory disconnect on an ATA 190.  I
> can’t use a router FXS port as the router is in another network closet.
>
> Am I missing something?
>
>
>
> Thank you,
>
> Vince
>
>
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20160722/265c720a/attachment.html>